Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 2 4/25/06
(35) THERMOSET (OR CHEMSET). A plastic that once set or molded cannot
be re-set or remolded because it undergoes a chemical change; (i.e., it is substantially
infusible and insoluble after having been cured by heat or other means.)
(36) WARP. Yarns extended along the length of the fabric (in the 0° direction)
and being crossed by the fill yarns (90° fibers).
(37) WORK LIFE. The period during which a compound, after mixing with a
catalyst, solvent, or other compounding constituents, remains suitable for its intended
use.
(38) CATASTROPHIC FAILURE. Any structural failure, which results in death,
severe injury, or loss of the aircraft.
(39) FATIGUE TOLERANCE. The capability of structure to continue
functioning without catastrophic failure after being subjected to fatigue (repeated) loads
expected during operation of the rotorcraft. Fatigue tolerance should be achieved by
flaw tolerance design, or if impractical, safe-life design, or a combination.
(40) SAFE-LIFE. The capability of as-manufactured structure as shown by
tests, or analysis based on tests, not to initiate fatigue cracks during the service life of
the rotorcraft or before an established replacement time.
(41) FLAW TOLERANCE. The capability of rotorcraft structure to achieve
fatigue tolerance accounting for the presence of flaws and damage that may occur in
manufacturing and service use. Flaw tolerance can be achieved by either flaw
tolerance safe-life or fail-safe designs. The term “Damage Tolerance” is frequently used
to describe the ability of a structure to tolerate the effects of flaws and damage;
however, the terminology of § 27.571, Amendment 26, is used in this AC to maintain
consistency.
(42) FLAW TOLERANT SAFE-LIFE. The capability of as-manufactured
structure, with expected flaws, as shown by tests or analysis based on tests, not to
initiate fatigue cracks or flaw/damage growth during the service life of the rotorcraft or
before an established replacement time.
(43) FAIL-SAFE. The capability of structure remaining after a partial failure to
withstand design limit loads without catastrophic failure within an inspection period.
(44) MULTIPLE LOAD PATH. Structure providing two or more separate and
distinct paths of structure that will carry limit load after complete failure of one of the
members.
(45) ACTIVE MULTIPLE LOAD PATH. Structure providing two or more load
paths that are all loaded during operation to a similar load spectrum.
Page MG 8 - 6
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.