FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 861

PDF page 861 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 861
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

4/25/06                                       AC 27-1B, Chg 2


critical load case has an associated maximum structural temperature). This term is
synonymous with the term “maximum panel temperature.”

        (25) POROSITY. A condition of trapped pockets of air, gas, or void within a
solid material, usually expressed as a percentage of the total nonsolid volume to the
total volume (solid + nonsolid) of a unit quantity of material.

        (26) PRE-PREG, PREIMPREGNATED. A combination of mat, fabric,
nonwoven material, tape, or roving already impregnated with resin, usually partially
cured, and ready for manufacturing use in a final product that will involve complete
curing. Pre-preg is usually drapable, tacky, and can be easily handled.

        (27) RESIN. An organic material with indefinite and usually high molecular
weight and no sharp melting point.

        (28) RESIN CONTENT. The amount of matrix present in a composite either by
percent weight or percent volume.

        (29) SECONDARY BONDING. The joining together, by the process of
adhesive bonding, of two or more already-cured composite parts, during which the only
chemical or thermal reaction occurring is the curing of the adhesive itself. The joining
together of one already-cured composite part to an uncured composite part, through the
curing of the resin of the uncured part, is also considered for the purposes of this
advisory circular to be a secondary bonding operation. (See COCURING).

        (30) SHELF LIFE. The lengths of time a material, substance, product, or
reagent can be stored under specified environmental conditions and continue to meet
all applicable specification requirements and/or remain suitable for its intended function.

        (31) STRAIN LEVEL. As used herein, is defined as the principal axial gross
strain of a part or component due to the principal load or combinations of loads applied
by a critical load case considered in the structural analysis (e.g., tension, bending,
bending-tension, etc.). Strain level is generally measured in thousandths of an inch per
unit inch of part or micro inches/per inch (e.g., .003 in/in equals 3000 micro inches/inch).

        (32) SYMMETRICAL LAMINATE. A composite laminate in which the ply
orientation is symmetrical about the laminate midplane.

        (33) TAPE. Hot melt impregnated fibers forming unidirectional pre-preg.

        (34) THERMOPLASTIC. A plastic that repeatedly can be softened by heating
and hardened by cooling through a temperature range characteristic of the plastic, and
when in the softened stage, can be shaped by flow into articles by molding or extrusion.




                                                        Page MG 8 - 5

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →