Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
(1) Background. Continuous climbs are conducted at the appropriate climb
airspeeds as outlined above in order to validate the rotorcraft’s climb performance.
By-products are a qualitative evaluation of the rotorcraft handling characteristics in a
climb and engine data to assist in the determination of installed power available.
(2) Techniques. The climbs are conducted on reciprocal headings at the
established airspeed(s) through the target altitude range. The same parameters are
recorded as during sawtooth climbs. The rotorcraft will usually climb very rapidly during
the first few thousand feet; therefore, the data acquisition method must be timely if
accurate results are expected. This procedure is usually repeated at weight extremes.
The resulting data must then be corrected for power and weight. Power and weight
corrections are satisfactory, provided the test powers and weights closely approximate
the target values to make the weight and power corrections small. Once this data is
finalized and corrected for all the flight test variables, interpolation for intermediate
weights can be made with a high degree of reliability. If the rotorcraft has any stability
augmentation system, vent systems, etc., which may influence the climb performance,
then it must be accounted for. Caution should be taken that anti-ice, air-conditioning,
etc., are not on unless the performance is being established specifically for those
conditions.
AC 27.65A. § 27.65 (Amendment 27-33) CLIMB: ALL ENGINES OPERATING.
a. Explanation. Amendment 27-33 added the requirement to determine the
steady rate of climb, for helicopters, from sea level up to the maximum altitude for which
certification is requested. Although not specifically stated in the rule, the rate of climb
should be determined at VY or, if VNE at any altitude is less than the maximum gross
weight sea level standard day condition VY, the steady rate of climb at these altitudes
must be determined at a climb speed(s) selected by the applicant not to exceed VNE.
b. Procedures. The policy material pertaining to the procedures outlined in this
section remain in effect.
AC 27.67. § 27.67 (Amendment 27-23) CLIMB: ONE ENGINE INOPERATIVE.
a. Explanation.
(1) Section 27.67 requires that for multiengine normal category rotorcraft, the
steady rate of climb or descent with one engine inoperative must be determined at VY
(or at the speed for minimum rate of descent) for maximum gross weight.
(2) The rate of climb (or descent) will be determined with the critical engine
inoperative and the remaining engine(s) at maximum continuous or 30-minute minimum
specification installed power available values. The landing gear should be retracted if it
is retractable.
Page B - 28
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.