FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page B-29

PDF page 87 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 87
AC 27-1B · B-29Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/17/2009                                       AC 27-1B, Chg 4


     b. Procedures.

         (1) The procedure discussed in paragraph AC 27.65 for all-engines-operating
climb performance is also applicable to the OEI condition. For twin-engine rotorcraft
that are shown not to have a “critical engine” with respect to performance
characteristics, both engines may be used to simulate the appropriate single-engine
power available during these tests.

         (2) Adequate testing must be accomplished to determine the rotorcraft’s OEI
climb performance at maximum gross weight for all variations in altitude and
temperature for inclusion in the Rotorcraft Flight Manual.

AC 27.71.   § 27.71 (Amendment 27-44) AUTOROTATION PERFORMANCE.

All of the policy material pertaining to this section remains in effect.

     a. Explanation.

         (1) Performance capabilities during stabilized autorotative descent are useful
tools to assist the pilot when all engines fail. This information is also useful in
determining the suitability of available landing areas along a given route segment.

         (2) Two speeds are of particular importance, the speed for minimum rate of
descent and the speed for best angle of glide. These speeds along with glide distance
information are required as flight manual entries per § 27.1587. The speed for minimum
rate of descent is useful for engine failure conditions at higher altitudes and the pilot is
required to perform some time-related task, engine restart, float inflation, radio calls, etc.
The speed for best angle of glide is a somewhat higher speed that is of particular use
when it is necessary to reach a distant landing area. These speeds, when utilized in
conjunction with appropriate rotor RPM and glide angle (or rate of descent) can be used
to calculate the maximum horizontal distance available from a particular altitude
assuming zero wind conditions.

         (3) A third speed, recommended autorotation speed, may be provided in
addition to minimum rate of descent speed and maximum glide angle speed. The
recommended speed for autorotation is usually optimized to assure an effective flare
capability and yet be slow enough to allow a controlled, relatively slow touchdown
condition. Recommended autorotation speed is ordinarily between the minimum rate of
descent and maximum glide angle speeds. The recommended autorotation speed may
be provided in the Rotorcraft Flight Manual. The relationship between minimum rate of
descent, best glide angle, and recommended autorotation speed is shown in
figure AC 27.71-1.

         (4) Forward center of gravity is usually critical; however, center of gravity
effects should be spot-checked to confirm this for a given design.


                                                       Page B - 29

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →