FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 858

PDF page 858 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 858
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 4                                                       3/31/2014


traditionally involved the generation of stress versus life or cycle (S-N) curves for each
critical part (most of which are subjected to the cyclic loading of the main or tail rotor
system) using a monotonic (sinusoidal) fatigue spectrum based on maximum and
minimum service stress values. Unless configuration differences or flight usage data
dictate otherwise, the monotonic fatigue spectrum’s period is typically based on six
ground-air-ground (GAG) cycles for each flight hour of operation. The S-N curves for
the substantiation of each detailed part are typically generated by plotting a curved line
through three data points (reference AC 27-1B, Chg 1, MG 11, “Fatigue Evaluation of
Rotorcraft Structure”). The three data points selected are a short specimen life
(low-cycle fatigue), an intermediate specimen life, and a long specimen life (high-cycle
fatigue). Each raw data point is generated by monotonically fatigue testing at least two
full-scale specimens (parts) to failure or run out for each data point on the S-N curve.
The raw data point values are then reduced by an acceptable statistical method to a
single value for plotting to ensure proper reliability of the associated S-N curve.
Order 8110.9, “Handbook on Vibration Substantiation and Fatigue Evaluation of
Helicopter and Other Power Transmission Systems” and AC 27-1B, Chg 1, MG 11,
“Fatigue Evaluation of Rotorcraft Structure,” contain comprehensive discussions of the
S-N curve generation process. The rotorcraft S-N curve process contrasts sharply with
the fixed wing process of using a single full-scale fatigue article (usually an entire wing
or airframe, which constitutes a single full-scale assembly data point), generic material
or full-scale assembly S-N data (e.g., MIL-HDBK-5 for metals, MIL-HDBK-17 for
composites, or AFS-120-73-2 for full-scale assemblies), a non-monotonic spectrum and
relatively large scatter factors to verify or determine the design fatigue life of the
full-scale airplane.

         (2) Also, rotorcraft have employed and mass-produced composite designs in
primary structure (typically main and tail rotor blades) since the early 1950’s. This was
10 or more years before composites were type certificated for primary fixed-wing
structure in either military or civil aircraft applications (with some notable limited
production exceptions, such as the Windecker fixed wing aircraft). In any case, the
early 1950 period was well before a clear, detailed understanding of composite
structural behavior (especially in the areas of macroscopic and microscopic failure
mechanisms and modes) was relatively common and readily available in a usable
format for the average engineer working in this field.  It also predated the initial issuance
of AC 20-107. Currently, much composite design information is proprietary, either to
government, industry, or both, and many data gathering methods have not been
completely standardized. Consequently, a significant variation from laboratory to
laboratory in material property value determination methods and results can exist. The
early rotor blade designs (as well as current designs) are by nature relatively low strain,
tension structure designs. Also, by nature, these designs are not damage or flaw
critical. Thus by circumstance as much as design, early composite rotor blade and
other composite rotorcraft designs incorporated an acceptable fatigue tolerance level of
safety. In the 1980’s, more test data, analytical knowledge, and analytical methodology
became available to more completely substantiate a composite design. Current 14 CFR
parts 27 and 29 contain many sections (reference paragraph a above) to be considered
in substantiating composite rotorcraft structure, but this advisory material is needed to


Page MG 8 - 2

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →