Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 2/27/2014
(iii) Maintenance. The maintenance requirements to ensure the serviceability
and continued airworthiness of the FDMS are typically established by the equipment
manufacturer and installer. These maintenance instructions should be included in the
applicable helicopter model instructions for continued airworthiness.
*(14) Radio Altimeter (RAD ALT). RAD ALTs installation is required. Its
information display must be in the pilot’s primary field of view in all helicopters operating
under a part 135 certificate. The minimum performance requirements for an FAA
approved RAD ALT system can be found in TSO-C87.
(15) Other EMS Equipment. These items of equipment installed for the EMS
mission are considered optional equipment and should be operated to ensure they
function properly. This evaluation would normally be done by someone knowledgeable
about the particular type of equipment, since correct operation of the equipment is
essential to a valid determination that the required rotorcraft systems are not being
interfered with. This includes all removable pieces of medical equipment that are used
for patient care. The primary purpose of the evaluation of this equipment is to
emphasize the possibility of any interference between operation of the EMS equipment
and the systems whose installation is required for safe operation of the aircraft, the
adequacy of the installation provisions, and assurance that failure modes will not result
in a hazardous condition for the rotorcraft.
(16) Miscellaneous. The following areas are not peculiar to EMS installations;
however, their significance is enhanced by the complexity of an EMS installation.
(i) Compatibility. Many EMS installations are a collection of several STCs and
may also include some FAA field approvals. For this situation, it should be shown that
the overall installation provides for safe operation of the aircraft. Operation of a search
light, if included, should be addressed since in using this system it can be difficult to
keep light from interfering with the pilot view.
(ii) Electrical Load Analysis. An electrical load analysis should be conducted,
and additional guidance is available in AC 27-1 MG 1. If the analysis indicates the
generator(s) can be overloaded, appropriate measures should be taken to account for
the problem. In some instances (e.g., in a visual flight rules (VFR) approved rotorcraft),
a placard that specifies certain operating limitations may be satisfactory, while in other
instances (e.g., in an instrument flight rules (IFR) approved rotorcraft), an electrical
interlock may be in order. In general, if the amount of overload is relatively small and
the rotorcraft is not an IFR-approved rotorcraft, the placard solution will probably be
satisfactory, whereas if the amount of possible overload is significant, it is more likely
that an interlock scheme will be necessary.
(iii) Aircraft Grounding. It should be emphasized in an appropriate place in the
STC data (e.g., RFM, maintenance information) that any time the EMS systems are
Page MG 6 - 18
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.