Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
2/27/2014 AC 27-1B, Chg 4
aircraft parameter data. The applicant determines and maintains the data stream
format and parameter documentation, including which parameters are recorded, how
often the parameters are recorded, the bit resolution of each parameter, the operational
range of each parameter, and the conversion algorithm from decimal units to
engineering units. The Design Assurance Level (DAL) for an FDMS that is required by
an operating regulation is DAL “D.” RTCA DO-178B (or later revision) provides
acceptable software development standards, which in this case would be for DAL “D”
software. RTCA DO-254 (or later revision) provides acceptable airborne electronic
hardware (AEH) development standards, which in this case would be for DAL “D” AEH.
Note: The duration between data downloads for the promotion of operational safety
within a FOQA program is directly correlated to the recording capabilities of the
system installed.
(ii) Recording. The FDMS should be capable of capturing and recording any
combination of the following parameters in order to monitor the aircraft’s state,
condition, and system performance:
• Positioning system time.
• Positioning system latitude.
• Positioning system longitude.
• Positioning system altitude.
• Positioning system error.
• Altitude.
• Heading.
• Pitch attitude.
• Pitch rate.
• Roll attitude.
• Roll rate.
• Yaw rate.
• Air speed.
• Ground speed.
• Ambient acoustic data.
• Engine parameters.
• Main rotor revolutions per minute.
• Transmission ambient audio.
• Any other parameters deemed appropriate by the operator.
Notes:Parameters may be recorded directly or deduced from recorded data from the
FDMS. Additional guidance on parameters can be found in EUROCAE
specification ED-155.
Recording individual pilots, using hot microphones, on separate pilot audio
channels can provide useful information in the investigation of incidents and
accidents.
Page MG 6 - 17
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.