Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
2/27/2014 AC 27-1B, Chg 4
consideration given to the manufacturer’s environmental qualification. Radio Technical
Commission for Aeronautics Document D0-160 is a recognized and accepted standard
for environmental considerations. As a minimum, consideration should be given to
operation during altitude, temperature, and vibration extremes.
(6) Placards. Appropriate, durable placards should be provided with the
installed system. Emphasis should be placed on any precautions that are appropriate
during filling of the system and so forth.
(7) Filler Connections. When a filler connection is provided, it is
recommended it be located outside the fuselage skin or isolated in a manner that would
prevent leaking oxygen from entering the rotorcraft. Careful evaluation should also be
made of any nearby sources of fuel, oil, or hydraulic fluid under normal or malfunction
conditions. Each filler connection should be placarded. In addition, any valve (on
aircraft or ground servicing equipment) associated with high pressure should be slow
acting.
(C) “Provisions Only” Considerations. In some instances, systems are
approved that only include provisions for a supply system consisting of the high
pressure cylinders, regulators, and their associated lines and fittings. In these
instances, a placard should be provided that refers to a supply system that is
considered satisfactory for the remainder of the installation. An example of an
acceptable placard for this situation is:
Oxygen Supply System must be in accordance with the requirements
given in STC SH _________. Deviations to the configuration specified
must be evaluated and approved by the Manager (include reference to the
appropriate FAA ACO).
(11) Medical Communication Equipment. This equipment is provided to allow for
communication between the rotorcraft and ground medical personnel. It includes voice
communication and may also include telemetry equipment for the transmission of
graphic data. It should be demonstrated that this equipment functions properly and the
range at which this determination was made recorded in the project file. The functional
demonstration should include a 360° turn (clockwise and counterclockwise) to ensure
no significant sections of signal blanking exist. The remainder of the emphasis on this
equipment should be to ensure that operation of this equipment does not interfere with
normal operation of any rotorcraft systems whose installation is required for safe
operation of the rotorcraft.
(12) Cabin Lighting. EMS interiors normally include higher intensity cabin lighting
than other interiors. This lighting capability should be carefully evaluated to ensure it
does not interfere with operation of the rotorcraft. In some installations, a special
curtain is required to separate the cockpit from any interference by the lighting. The
FAA approved data should document the approach of how this evaluation was
conducted. See paragraph b.(6) for other curtain considerations.
Page MG 6 - 15
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.