Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 2/27/2014
(6) System Marking. The rotorcraft should be permanently and legibly
marked, as applicable, in the locations specified below (a minimum letter height of
¼-inch is recommended):
(i) Adjacent to the overboard vent opening:
CAUTION
LIQUID OXYGEN VENT
(ii) On outside surface of filler box cover plate:
LIQUID OXYGEN (BREATHING) FILL ACCESS
(iii) On underside surface of filler box cover plate:
CAUTION - KEEP CLEAN, DRY, AND FREE FROM OILS
(iv) In prominent place when filler box is open, preferably near liquid
oxygen drain valve:
DO NOT OPEN DRAIN VALVE UNTIL DRAIN HOSE
AND DRAIN TANK ARE CONNECTED
(v) Other placards, such as one at the converter cautioning about the
presence of liquid oxygen, may also be appropriate.
(7) Other installation criteria are given in Chapter 6 of AC 43.13-2,
Acceptable Methods, Techniques, and Practices-Aircraft Alterations, and should be
given consideration.
(D) Precautions. The referenced Society of Automotive Engineers (SAE)
report contains precautions peculiar to a liquid oxygen installation, and this material
should be reviewed. It should also be emphasized that liquid oxygen equipment and
the aircraft being serviced must be electrically grounded during servicing to prevent an
accumulation of static electricity and discharge. The following considerations are
included for special emphasis:
(1) System Cleanliness. The completed installation should be free of oil,
grease, fuels, water, dust, dirt, objectionable odors, or any other foreign matter, both
internally and externally prior to introducing oxygen in the system.
(2) Closures. Lines that need to be disconnected during rotorcraft
maintenance checks or overhaul, due to the location of the converter within the
rotorcraft, should be capped to prevent materials that are incompatible with oxygen from
entering the system when the system integrity is broken. Caps that introduce moisture
and tapes that leave adhesive deposits should not be used for these purposes. All
Page MG 6 - 12
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.