Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 2/27/2014
indicator when installed in the rotorcraft should indicate the amount of liquid oxygen in
the converter. Adequate clearance should be provided for the indicator connectors so
that they can be readily disconnected by servicing personnel. Provisions should be
made for the storage of the rotorcraft connectors to the liquid oxygen converter when
they are disconnected. Liquid oxygen quantity indicating equipment is available in three
types: capacitance gauging, electro-mechanical transducer indication, and differential
pressure type indication.
(12) Pressure Relief Valves. Pressure relief valves are provided to vent
overboard through the overboard vent system any excess pressures developing within
the system.
(13) Lines. Lines should be either solid tubing or flexible hoses.
Examples of acceptable solid tubing are aluminum alloy conforming to AMS 4071 or
corrosion resistant annealed steel (304) confirming to MIL-T-8506. Flexible hoses
should be used for rotorcraft system connections to removable converters and to other
applications where relative movement may occur. Flexible hoses should be wire-braid
covered bellows or wire-braid-covered tetrafluoroethylene. Flexible hoses conforming
to MS90457 or MS24548 are satisfactory. MS90457 hose is flexible to -297°F (-183°C),
and MS24548 hose is flexible to -65°F (-54°C). Synthetic lines such as plastic, nylon, or
rubber should not be used for lines subjected to continuous pressure, or for application
where the line will not be visible. Lines that are not visible are those that are located
behind liners or in the walls of the fuselage.
(14) Fittings. If in contact, dissimilar metals should be suitably protected
against electrolytic corrosion. Line assemblies should be terminated with “B” nuts or a
similar manufactured terminating connection. Universal adapters (AN 807) or friction
nipples used in conjunction with hose clamps should be avoided in pressurized
systems.
(15) Drain Valve. Systems that have permanently installed containers
should include a drain valve located to allow for complete draining of the liquid oxygen
container. An acceptable drain valve would be one in accordance with MK-V-25962
that is suitably capped. A cap in accordance with AN 929-5 with a permanently
attached chain is a suitable cap.
(16) Low Pressure, Low Level Warning System. It is recommended that
provisions be included in the system to alert the appropriate aircraft crew member that
the level of the oxygen supply has reached some low level. It is recommended that low
level be actuated when less than 10 percent of the full container capacity is available. If
low system pressure is also monitored, the low pressure valve selected should be such
that any drop in supply line pressure upon inhalation should not activate the low
pressure warning function.
(C) Component Installation. The following are typical installation
considerations that should be addressed when designing the oxygen system.
Page MG 6 - 10
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.