Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 2/27/2014
(4) Flammability of Materials.
(i) Interior materials must meet the flammability standards in § 27.853,
appropriate to the type design. The standard presently requires compartment materials
to be at least flame resistant. The wall and ceiling linings, coverings of upholstery,
floors, and furnishings must be at least flame resistant.
(A) Flash-resistant material may be characterized as that not exceeding a 20-
inch-per-minute (horizontal) burn rate. See AC 23-2, Flammability Tests, for further
information.
(B) Flame-resistant material may be characterized as that not exceeding a 4-
inch-per-minute (horizontal) burn rate.
(C) Self-extinguishing materials that can meet the transport rotorcraft
standards of § 29.853 of Amendment 29-17 are recommended for use in normal
category rotorcraft.
When the isolette is included in the EMS configuration approval, the isolette materials
are subject to the flammability standards of § 27.853. The current standards require
that all materials, including transparencies, fabric (e.g., padding, covers), straps, etc., be
flame-resistant for each compartment used by the crew or passengers. AC 23-2 also
contains test information about flash and flame-resistant material.
(5) Exit Signs or Markings and External Markings. Doors and exits must have
signs and markings (instructions) for prompt evacuation even in darkness. An
emergency light system is not required by part 27. Refer to the RFM or maintenance
manual for standard placards, decals, stencils, etc. Alternates may be approved as a
part of the interior type design.
(6) Interior or “Medical” Lights. The view of the flightcrew must be free from glare
and reflections that could cause interference. Use of a night vision imaging system
(NVIS) should be a consideration in this evaluation. Curtains that meet the flammability
standards (flame resistant) may be used. Complete partitioning or separation of the
flightcrew and passenger area is not prudent. Means for visual and oral communication
are usually necessary. Refer to AC 27-1 section 27.773, which concerns pilot visibility.
(7) Patient Interference. When passengers or patients are located in close
proximity to the pilot and the primary flight controls of the rotorcraft, a guard or shield
should be installed, or the patient should be restrained to prevent inadvertent or
potential patient interference with safe operation of the rotorcraft. The guard may be a
part of the rotorcraft interior features. In addition, prompt evacuation should be ensured
if a guard is used.
Page MG 6 - 6
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.