Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
2/27/2014 AC 27-1B, Chg 4
materials are also subject to the flammability standards noted in paragraph b.(4). The
litter(s) and isolette(s) should be listed in the type design data for the EMS
configuration.
(iii) An isolette used for the transport of infants presents a special case, in that it
may be included as part of an approved EMS configuration or it may be carried on the
rotorcraft as needed for transport of infants. If the isolette is self-contained and is not
part of an EMS type design, it may be considered a carry-on item and not part of the
EMS type design. In these cases, there is typically a means to position the carry-on
isolette and properly restrain the isolette for transport as part of the EMS design
configuration.
(A) When the isolette is carry-on equipment, the operator must ensure that
the isolette does not create a safety risk or interfere with aircraft operations. AC 135-14,
Emergency Medical Services/Helicopter (EMS/H), provides information and guidance to
air ambulance and EMS/H operators for large carry-on medical equipment such as
isolettes. AC 135-14 includes the provision that isolettes are to be restrained in an
appropriate manner and evaluated for specific emergency landing load factors as
required by earlier amendments of the rotorcraft regulatory requirements. Since
publication of AC 135-14, the emergency landing load requirements have changed for
rotorcraft. Consequently, the load factors specified in that AC may not be appropriate
for some rotorcraft, depending on the rotorcraft certification basis amendment level of
the airworthiness standards. The minimum load factors should be no less than those
specified in the certification basis of the rotorcraft transporting the medical equipment,
such as isolettes.
(B) A placard indicating that the isolette should be evaluated per the
guidance contained in AC 135-14 and restrained to the emergency landing load factors
for rotorcraft occupants per 14 CFR 27.561(b)(3), or the appropriate reference based on
the certification basis of the rotorcraft, should be placed in close proximity to the isolette
mount location.
(iv) Galleys, medical supplies, and equipment compartments or modules should
be restrained and the individual compartments should also contain the contents for the
conditions noted in paragraph b.(3) of this guidance. Durable placards, decals, or
markings should be used where appropriate to limit the maximum weight of any
compartment and the whole module. Compartment latches having sufficient strength
and displacement or engagement should be used to contain the contents for the
conditions noted in paragraph b.(3) of this guidance. If necessary, a static load test or
analysis should be employed to ensure the container or compartment remains intact
and the latch does not disengage for the most critical conditions. Loose or unrestrained
contents in an individual compartment, in combination with similar compartments,
should use a magnification factor with the design conditions. Prudent design and
location of compartments having heavy, unrestrained (loose) equipment will mitigate the
potential effects of landing impact loads.
Page MG 6 - 5
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.