FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 835

PDF page 835 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 835
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/27/2014                                      AC 27-1B, Chg 4


appropriate to reference the helicopter manufacturer’s “standard” features, placards,
and markings in the applicant’s modification design data.

             (ii) The EMS modification presented for approval usually contains equipment of
one manufacturer’s model or design. The type design of the modification will have
features to power and restrain the equipment, maintain the rotorcraft systems integrity,
and to otherwise protect the occupants. See paragraph b.(17), which refers to
equipment substitution.

              (iii) All equipment installations in the helicopter must be approved. EMS
helicopters typically include operations in which large medical equipment is not installed
in the helicopter but instead is carried onto the helicopter, as needed, such as isolettes,
large medical equipment, and other medical items. This equipment is not included as
part of the rotorcraft type design modification because it is not considered a permanent
installation in the helicopter. However, carry-on medical equipment must be evaluated
as to how it affects the safety of the helicopter and its occupants (including the occupant
in the isolette) while being carried in the helicopter. This carry-on equipment (including
the isolette) must be properly restrained so it is not a hazard during flight operations.
Consequently, the means to stow or store the medical carry-on items must be evaluated
for the appropriate load factors relative to the helicopter such that the means for
stowage of the carry-on equipment does not fail. For instance, in the case of a carry-on
isolette, the isolette is typically placed on top of an installed “mount” for the isolette. The
“mount” is evaluated for carriage and restraining of the isolette. In some cases, an
isolette may be completely self-contained and include other items, such as oxygen
bottles required for the isolette occupant, which must also be evaluated for carriage of
that equipment.

      (2) Evacuation and Interior Arrangements. Access to the emergency exits or
doors from any location in the cabin or compartment, access to and use of the exit or
door opening means or release device, and the unobstructed area of an exit are
potential problems that should be addressed in the early design stage.  Multi-litter
arrangements may be especially critical for normal category rotorcraft due to their
limited space.

            (i) The operation or use of devices for locking the position of swivel seats and
for rapid installation and removal of litters (isolettes, etc.) should be labeled unless they
are simple and obvious, and do not require exceptional effort. The design features of
the device(s) and the seat or litter will influence the extent of information in any label
necessary to ensure proper and safe installation for routine use and prompt evacuation
when appropriate or necessary for the interior arrangement. The requirement for labels
or markings (instructions, etc.) that applies to operation of seat or litter features, release
devices, etc., is not relieved even if attendants are necessary for an evacuation as
discussed in paragraph b.(2)(iii). Placards or instruction cards that contain evacuation
procedures do not necessarily contain detailed procedures for individual seats, litters,
and so forth. Release devices that are simple and obvious and do not require
exceptional effort are recommended. For example, a single central control for litter


                                                        Page MG 6 - 3

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →