Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
12/15/2009 AC 27-1B, Chg 4
(10) Recent service history has shown that external equipment and external fixture
modifications that generate high drag loads in forward flight can affect main rotor mast
bending loads. In lieu of a mast bending survey, a pre and post modification flight test
may be conducted at identical weights, center-of-gravity (CG), power, and density
altitude to compare a critical control position parameter (typically longitudinal cyclic stick
position) at pre and post modification VNE airspeeds.
(i) If required, the post modification VNE should be reduced so that the post
modification longitudinal cyclic stick position is slightly aft of (or less than) the pre
modification stick position. This alternative procedure assumes that the static
longitudinal stability of the helicopter has not been altered by the modification. For
helicopters with neutral static stability, a more comprehensive investigation may be
required.
(ii) In some cases, a control position parameter other than longitudinal stick
position may be critical. For example, a heavy external device mounted to the side of
the helicopter that gives a lateral CG close to the limit and an asymmetric yaw
component would require pre and post modification lateral cyclic stick and pedal
position measurements. Operating limitations other than VNE may need to be
established, or reduced from pre-modification limitations, to ensure pre-modification
mast bending is not exceeded.
(11) For rotorcraft certificated in dual categories, the inspection requirements of
§ 21.187(b) must be observed when converting from restricted to normal category.
c. Acceptable Means of Compliance.
(1) Analysis Method. Static structural analysis may be used provided a
methodology is applied that has been shown to be reliable for analyzing the type of
structure. Structural substantiation of tanks that are designed to contain liquid materials
may be accomplished by pressure testing. For tanks or hoppers designed to contain dry
material (e.g., dust or fertilizer), static load tests may be used to verify structural
integrity. The tank/hopper, mounting hardware, and support structure should all be
substantiated to the load conditions specified and should consider the effects of internal
fluid pressures, when applicable, in Figure AC 27 MG 5-1.
(2) Static Tests. Static tests of tank/hoppers, mounting hardware, and support
structure for each critical load condition may be accomplished using conventional
techniques; such as, dead weight loading, whiffletree systems, and hydraulic rams. If
tests of the tank and its mounting hardware are conducted using a test fixture
representing the rotorcraft, the rotorcraft support structure may be substantiated
independently by means of test or analysis, or both. Static test loads should be applied
in combination with associated internal fluid pressure loadings. The ultimate loads
specified in Figure AC 27 MG 5-1 should be sustained for at least 3 seconds without
failure.
Page MG 5 - 5
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.