Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1BChg 4 12/15/2009
(3) Dynamic Tests.
(i) If the applicant elects to test to the loading conditions in Figure AC 27 MG 5
1, the maneuvering and gust loadings will be considered to be adequately
substantiated. For each condition, the critical volume and density of fluid should be
used.
(ii) The tank and mounting hardware should support ultimate loads without
permanent elastic deformation failure, respectively. The rotorcraft support structure may
be included in the dynamic tests, or it may be substantiated separately via static test or
analysis, or both, for each condition specified in Figure AC 27 MG 5-1.
(4) Pressure Testing. Internal pressure loads may be applied using the water
standpipe technique. Standpipe water height should be accurately computed for each
critical spray tank static test loading. Pressure testing of spray tanks is not absolutely
essential but is recommended for safety reasons. This testing will also determine
whether the joints and connections are tight and will not leak in addition to determining
any weak spots in the construction. Where spraying is done with highly volatile and
flammable liquids, or where the tank has a return line, such as in an engine oil tank
where the fluid is pumped back into the tank, it is recommended that the tank be tested
for a pressure of 5 pounds per square inch. For other liquids, and where no fluid return
line is used, testing to 3 ½ pounds per square inch should be satisfactory. There are
many ways of pressure testing a tank, however, it is believed that the simplest and
easiest method is to fill the tank with water and use a standpipe filled with water. A
1 1/8-inch pipe can be connected to the venting tube or one adapted to the filler
opening. In either case, the height of the pipe would be the same. For a 3 ½ PSI test of
the tank, the height of the water in the pipe would only need to be 8 feet and for a 5 PSI
test only an 11 ½ -foot height of water will be needed. (See Figure AC 27 MG 5-2
below.)
Page MG 5 - 6
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.