FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 827

PDF page 827 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 827
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

12/15/2009                                     AC 27-1B, Chg 4


*Requires acceptance by the cognizant Flight Standards District Office

Note: Some rotorcraft manufacturers have qualified certain locations on the underside
of their aircraft for mounting external equipment. The manufacturers will typically
specify external equipment weight and dimensional limitations at those locations. The
applicant should contact the manufacturer to see if this information is available as it
could be used to reduce the applicant's certification effort.

      (2) The critical structural loading conditions for substantiating the installation of
agricultural dispensing equipment can be developed by using the associated occupant
protection load factors provided in Figure AC 27 MG 5-1. These load factors are
prescribed to prevent dispensing equipment from causing injuries to occupants in the
event of an emergency landing. To ensure this, adequate margins of safety should be
used in the structural design consideration of dispensing equipment and dispensing
equipment installations.

______________________________________________________________________

                       FIGURE AC 27 MG 5-1
             ACCEPTABLE ULTIMATE LOAD FACTOR FOR
           AGRICULTURAL DISPENSING EQUIPMENT DESIGN

                       UP   DOWN   SIDE  FORWARD    AFT

Tanks & Equipment Mounted      1.5g      4.0g     2.0g      4.0g           - - - -
In Or Near The Fuselage                                   Note 1

Spray Booms                    1.5g      2.5g       - - - -     Note 1       2.5g
                                                                   Note 2

Note 1: An ultimate load factor of 2 G’s is acceptable for externally side or under
fuselage mounted tank and forward mounted spray booms where failure in a minor
crash landing will not create a hazard to occupants or prevent an occupant’s exit from
the rotorcraft.

Note 2: The aft loads for spray booms may be developed by the applicant based on the
111 percent of VNE for which certification is requested or the load factors of Figure
AC 27 MG 5-1, whichever is greater.
______________________________________________________________________


      (3) The applicant may elect to substantiate their product by either static or dynamic
testing, by analysis, or any combination thereof.




                                                        Page MG 5 - 3

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →