FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 821

PDF page 821 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 821
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

   4/25/06                                        AC 27-1B, Chg 2

   are similar and result in the same methods for compliance. A note has been added to
   the type certificate data sheets for rotorcraft that employ FADECs. This note was added
    to remind all modifiers that the requirement for addressing interference exists and that
   special EMI test considerations must be addressed to show compliance. Most EMC
   considerations can be addressed by the operational interference checks addressed in
   the background discussion. However, when a critical control function is provided by
  some electronic means, special EMI test considerations must also be addressed, in
   addition to the previously described EMC tests. The determination of when these other,
   more rigorous tests are required is a simple concept, but complex in practice. More
   rigorous testing is required to satisfy the concern for the installation of equipment that
   would interfere with the critical control (e.g., FADEC, Fly-By-Wire, etc.) or failure
   management of the critical control. This class of equipment is “equipment known to
   have a potential for interference,” which may or may not be qualified to an aircraft
   standard, such as high frequency (HF) radios, high powered radars, hoists, transmitting
   antennas located near the controls systems, etc. The concern associated with this
   class of equipment is the possible interference with the critical electronic controls.

                         (ii)   Accomplishment. In addition to the following special testing
   considerations addressed in paragraph (2)(iii), “EMI Installation Testing for Critical
   Controls” and “Installation Test Conditions,” all installed equipment should undergo a
   cross-matrix operational check for EMC considerations by operating all equipment
   under consideration and determining if an interference hazard is created.

                 (A) Class of Equipment - Equipment Known to Have a High Potential for
   Interference: This class of equipment should be tested in the installation as described
    in the “EMI Installation Testing for Critical Controls/Installation Test Conditions,”
   paragraph (2)(iii). Since the concern of this class of equipment is its high potential for
    interference, its EMI laboratory qualification does not preclude the EMI installation
    testing.

   Equipment that meets any one of the following criteria is considered to be “equipment
   known to have a high potential for interference.”

•  Equipment that requires 25 amps or more to operate,

•  Equipment that transmits 30 watts or more,

•  Equipment with an antenna located 0.5 meters or less from the FADEC, or

•  High Frequency (HF) Transmitters of any power.

   The types of equipment in this class include HF radios, high-powered radars, hoists,
   high-powered radios, installations where radio transmission antennas are in close
   proximity to the controls, and equipment that require large currents to operate or radiate
   strong electromagnetic fields. Examples of this type of equipment are some Emergency



                                                         Page MG 4 - 11

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →