FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 806

PDF page 806 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 806
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

         (1) Category A Minimum Time for Isolation. The acceptance of a limited time
period for engine isolation is consistent with the acceptance of a reduced level of safety
for a Part 27 rotorcraft. The criteria is also consistent with the Part 27 philosophy of
allowing for a controlled landing following engine failure versus the Part 29 Category A
principle of continued safe flight and a controlled landing.

         (2) Installation Analysis.

                  (i)   The degree of engine isolation can be established by an installation
assessment against the § 29.903(b) general isolation requirement, as modified for
Part 27 by a limited time period concept.

                   (ii)   Figure AC 27 MG 3-1 is a listing of the Part 29 sections that may be
involved in Category A engine isolation considerations. Sections 29.901(c) and
29.903(b) are the general isolation regulations under which the other more specific rules
naturally fall. The point that the selection of specific rules from figure AC 27 MG 3-1
does not achieve the desired degree of transport Category A engine isolation, and that
the general isolation rules (§§ 29.901(c) and 29.903(b)) must be used, is illustrated by
the following examples.

              (A) Example #1. No specific requirement from Part 29 (or figure AC 27
MG 3-1) can be cited which precludes a common engine mount. The design of the
mount could be such that its failure results in sudden, complete power loss from all
engines.

              (B) Example #2. No specific Part 29 requirement prohibits a common
engine induction system. F.O.D., fire in the induction system, or the adverse affect of
engine surge on the remaining engine could result in sudden, complete power loss from
all engines.

             (C) Example #3. Crosstalk between engine fuel controls (possibly used
for power matching) or the use of a common input parameter signal to the fuel controls
is not prohibited by any specific isolation rule. Signals could be received which
command the simultaneous shutdown of all engines.

                    (iii)  These examples clearly illustrate that specific Part 29 isolation rules
cannot be selected to establish appropriate Part 27 engine isolation, and that the
installation must be evaluated by the general isolation policy set forth. This can be
readily accomplished by a failure mode and effects analysis (FMEA).

         (3) Firewalls.

                  (i)  CAR 6.483, prior to Amendment 6-4, effective May 15, 1953, requires
“All engines, auxiliary power units, fuel burning heaters, and other combustion
equipment which are intended for operation in flight shall be isolated from the remainder



Page MG 3 - 2

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →