FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 791

PDF page 791 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 791
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 7                                                       2/4/2016


             (C) Stability. While observing a target return on the radar indicator, turn
off the stabilizing function, then put the aircraft through pitch and roll movements.
Observe the blurring of the display. Turn the stabilizing mechanism on, then repeat the
roll and pitch movements. Evaluate the effectiveness of the stabilizing function in
maintaining a sharp display.

             (D) Ground mapping. Fly over areas containing large, easily identifiable
landmarks such as rivers, towns, islands, coastlines, etc. Compare the form of these
objects on the indicator with their actual shape as visually observed from the cockpit.

              (E) Mutual interference. Determine that no objectionable interference is
present on the radar indicator from any electrical, radio, or navigational equipment when
operating, and that the radar installation does not interfere with the operation of any of
the rotorcraft’s radio or navigational systems.

       (11) Area Navigation. ACs 20-138 and 90-100 (current versions) contain the
basic criteria for evaluating an area navigation system, including acceptable means of
compliance to the Federal Aviation Regulations.

       (12) Inertial Navigation. AC 20-138 (current version) is the basic criteria for the
engineering evaluation of an inertial navigation system (INS) and offers acceptable
means of compliance with the applicable FA Regulations, which contain mandatory
requirements in an objective form. For flights up to 10 hours, the radial error should not
exceed two NM per hour of operation on a 95 percent statistical basis. For flights longer
than 10 hours, the error should not exceed ±20 NM cross-track or ±25 NM along track
error. A circle represents the two NM radial errors having a radius of two NM, centered
on the selected destination point.

       (13) Doppler Navigation. Evaluate doppler navigation system installed
performance in accordance with RTCA Document DO-158, “Minimum Performance
Standards – Airborne Doppler Radar Navigation Equipment.”

       (14) Radio Altimeters. Evaluate radio altimeter system installed performance in
accordance with RTCA Document DO-155 (current version).

       (15) Emergency Locator Transmitters (ELT).

               (i) Evaluate ELT performance in accordance with TSO-C126. Examine ELT
installations for potential operational problems. There have been numerous instances
of interaction between ELT and other VHF installations. ELT antenna installations in
close proximity to other VHF antennas should be suspect. Measure the patterns of
previously installed VHF antennas after an ELT installation. Some problems caused by
ELT installations are:

              (A) Loss of radiated power from VHF communications.



Page MG 1 -12

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →