Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 7 2/4/2016
(A) Long range reception. Perform two 360° turns, one to the right and
one to the left, at a bank angle of 8° to 10° at least 80 NM from the DME facility. A
single turn will be sufficient if the antenna installation is symmetrical. There should be
no more than one unlock, not to exceed one search cycle (maximum 35 seconds), in
any 5 miles of radial flight.
(B) Approach. Make a normal approach to land at a field with a DME
located on the airport. The DME should track without an unlock (station passage
excepted).
(C) DME hold. With the DME tracking, activate the DME hold function.
Change the channel selector to a localizer frequency. The DME should continue to track
on the original station.
(9) Transponder Equipment.
(i) Performance Criteria. The ATC transponder system should furnish a
strong and stable return signal to the interrogating radar facility when flying the rotorcraft
in straight and level flight throughout the air space within 80 NM of the radar station
from radio line of sight to within 90 to 100 percent of the maximum altitude for which the
rotorcraft is certificated. The airborne system should be controllable so that
objectionable ring-around, spoking, and clutter will not persist. The transponder system
should not interfere with other systems aboard the rotorcraft and other equipment
should not interfere with the operation of the transponder system (some interference
from DME operation may be acceptable). When flying the rotorcraft in the following
maneuvers within the airspace described above, the dropout time should not exceed
20 seconds.
(A) In turns at bank angles up to 10°.
(B) Climbing and descending at normal maximum climb and descent
attitude.
(C) Orbiting a radar facility.
(ii) Technique.
(A) Climb and distance coverage. Beginning at a distance of at least
10 NM from and at an altitude of 2,000 to 3,000 feet above that of the radar facility and
using a transponder code assigned by the ARTCC, fly on a heading that will pass the
rotorcraft over the facility. At a distance of 5 to 10 NM beyond the facility, operate the
rotorcraft to maintain an altitude above radio line of sight while maintaining the aircraft at
a heading within 5° from the radar facility to 80 NM from the radar facility.
(B) Communicate with the ground radar personnel for evidence of
transponder dropout. During the flight, check the ”ident” mode of the ATC transponder
Page MG 1 -10
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.