FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 787

PDF page 787 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 787
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 7                                                       2/4/2016


Note: We recognize that the normal altitude at the middle marker is approximately 150
       to 200 feet. Due to variations in both glide slope angle and position of the middle
      marker in relation to the runway, the on glide path marker width will vary
       considerably, which in turn will give a widely varying light time. Therefore, use
      the more clearly defined criteria at 1,000-feet altitude for quantitative testing of
      the middle marker function.

       (7) Automatic Direction Finding Equipment (ADF).

               (i) Range and Accuracy. The ADF system installed in the rotorcraft should
provide operation with errors not exceeding 5° and the aural signal should be clearly
readable up to the distance listed for any one of the following types of radio beacons:

              (A) 50 NM from an homing (H) facility (transmitter power at
50-2,000 watts).

              (B) 25 NM from an medium homing (MH) facility (transmitter power less
than 50 watts).

             (C) 15 NM from a compass locator (transmitter power less than 25 watts).

                (ii) Needle Reversal. The ADF indicator needle should make only one 180°
reversal when the rotorcraft flies over a radio beacon. Make this test both with and
without the landing gear extended.

                 (iii) Indicator Response. When switching stations with relative bearings
differing by approximately 175°, the indicator should indicate the new bearing within ±5°
within 10 seconds.

             (iv) Antenna Mutual Interaction. For dual installations, there should not be
excessive coupling between the antennas.

            (v) Technique.

              (A) Range and accuracy. Tune in a number of radio beacons spaced
throughout the 200 to 415 kHz range and located at distances near the maximum range
for the beacon (see paragraph b.(7)(i), Range and Accuracy, above). The identification
signals should be clear and the ADF should indicate the approximate direction to the
stations. Beginning at a distance of at least 15 NM from a compass locator in the
approach configuration, fly inbound on the localizer front course and make a normal
instrument landing system (ILS) approach. Evaluate the aural identification signal for
strength and clarity and the ADF for proper performance with the receiver in the ADF
mode. All electrical equipment on the aircraft should be operating and all pulse
equipment should be transmitting. Fly over a ground check point with relative bearings



Page MG 1 -8

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →