FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 786

PDF page 786 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 786
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/4/2016                                      AC 27-1B, Chg 7


                (ii) Glide Slope Intercept. While flying the localizer course inbound in level
flight, intercept the glide slope below path at least 10 NM from the station. Observe the
glide slope deviation indicator for proper crossover as the aircraft flies through the glide
path. No flags should appear between the times the needle leaves the full-scale fly-up
position and it reaches the full-scale fly-down position.

                 (iii) Glide Slope Tracking. While tracking the glide slope, maneuver the
aircraft through normal pitch and roll attitudes. The glide slope deviation indicator
should show proper operation with no flags. Conduct at least three acceptable
approaches to 200 feet or less above threshold.

             (iv) Interference. With all rotorcraft electrical equipment operating and all
pulse equipment transmitting, determine that there is no interference with the glide
slope operation (some interference from the VHF may be acceptable), and that the glide
slope system does not interfere with other equipment.

            (v) Glide slope performance should be checked for rotor modulation during
the approach while varying rotor RPM throughout its normal range.

       (6) Marker Beacon System.

               (i) The marker beacon annunciator light should be illuminated for a period of
time representing 2,000 to 3,000 feet distance when flying at an altitude of 1,000 feet as
it passes over a marker beacon as follows:

                                Altitude = 1,000 feet (AGL)

                    Ground Speed Light Time (Seconds)

                  Knots           2,000 feet         3,000 feet

                  90              13              20
                 110              11              16
                 130              9               14
                 150              8               12

                (ii) The audio signal should be of adequate strength and sufficiently free from
interference to provide positive identification.

                 (iii) Technical. Approach the markers at a ground speed of 130 knots and at
an altitude of 1,000 feet above ground level. While passing over the outer and middle
markers with the localizer deviation indicator centered, the annunciators should
illuminate for 9 to 14 seconds. Check for acceptable intensity of the indicator lights in
bright sunlight and at night. For slower rotorcraft, the interval should be proportionately
longer.


                                                        Page MG 1 -7

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →