Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 2 4/25/06
landing gear or flaps by alternate means, approach in multiengine aircraft with
inoperative engine(s), etc.
(ii) Emergency procedures are concerned with foreseeable but unusual
situations in which immediate and precise action by the crew, as detailed in the
recommended procedures, may be expected to reduce substantially the risk of disaster.
Typical examples of incidents considered to be emergencies are fire, ditching, loss of
tail rotor thrust or control, etc. It is expected that, in the case of tail rotor failure, the
emergency procedures will have been validated by analysis, simulation, or any relevant
service experience. The analysis or simulation of the tail rotor control failure procedures
may be validated where practical by limited flight test.
(iii) Amendment 27-11 added ditching standards to Part 27. When
ditching approval is requested, appropriate procedures and information will be included
in the manual. Scale model tests are generally used to prove autorotation “ditching”
characteristics and to prove stability in the water (capsize threshold) of the rotorcraft
type design. Many rotorcraft designs require emergency float bags that deploy either
before water contact or shortly after water contact to provide the flotation and stability
necessary to comply with the requirements.
(A) Autorotation altitudes and airspeeds and water contact information, if
appropriate, derived from or used during the ditching model tests, should be confirmed
during FAA/AUTHORITY flight tests and should be included in the manual. Information
concerning sea states or wave height to length ratios, investigated and found
satisfactory, may be included in the manual if nonsevere sea states are likely to be
exceeded.
(B) Instructions for deploying liferafts may be needed for certain designs.
For example, if liferafts are stowed outside the cabin, special instructions may be
necessary.
(iv) Evacuation Procedures for Rotorcraft Litter Configurations.
Appropriate procedures and minimum crew requirements should be considered and
included in the manual or manual supplement, if necessary, to assure timely
evacuation.
Page G - 44
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.