FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page G-43

PDF page 770 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 770
AC 27-1B · G-43Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

4/25/06                                       AC 27-1B, Chg 2


                  (i)    “Note” should be used with respect to matters not directly related to
safety but which are particularly important (e.g., Note: For normal twin-engine
operation, maximum permissible torque needle split is 4 percent total).

                   (ii)   “Caution” should be used with respect to safety matters of a
secondary order not immediately imminent (e.g., Caution: On engine restart reduce ITT
to 750° C on the operating engine).

                    (iii)   “Warning” should be used with respect to safety matters of a primary
order or immediately imminent (e.g., Warning: Do not allow rotor RPM to drop below
minimum limits).

         (3) The operating procedures of this section have been developed with specific
regard for the design features and operating characteristics of the rotorcraft and have
been approved by FAA/AUTHORITY for guidance in identifying acceptable procedures
for safe operation. Observance of these procedures is not mandatory, and
FAA/AUTHORITY approval of such procedures is not intended to prohibit or discourage
development and use of improved or equivalent alternate procedures based on
operational experience with the rotorcraft. When alternate procedures are used, full
responsibility for compliance with applicable airworthiness safety standards rests with
the operator.

     b. Procedures. Procedural information should be presented in substantial accord
with the categories described below:

         (1) Normal Procedures. Normal procedures are concerned with peculiarities of
the rotorcraft design and operating features encountered in connection with routine
operations, including malfunction cases not considered in the other procedures section
(i.e., not considered to degrade safety). Material conforming to the above should be
presented for each phase of flight, following in sequence from preflight through engine
shutdown, and should include, but not be limited to, systems operation (including fuel
system information prescribed in § 27.1585(b)), missed approaches, balked landings,
etc.

         (2) Emergency Procedures.

                  (i)    Malfunction or abnormal procedures are included in many flight
manuals to provide corrective crew actions that are not as urgent as those in the
Emergency Procedures sections. These procedures are concerned with foreseeable
situations, usually entailing a failure condition, in which the use of special systems, or
the alternate use of regular systems, may be expected to maintain an acceptable level
of safety. Typical examples of events considered to entail abnormal procedures are
engine failure or conditions that require an engine shutdown (under flight conditions
where the failure is not critical), stopping and restarting engines in flight, extending



                                                       Page G - 43

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →