FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page G-31

PDF page 758 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 758
AC 27-1B · G-31Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

     b. Procedures.

         (1) The placard must specify the kinds of operations, such as VFR, IFR, day,
night, or icing for which the rotorcraft is equipped and approved.

         (2) A placard (or durable decal) must be legible to the pilot and located in clear
view of the pilot.  If two pilots are required, a single placard may satisfy the standard.
This aspect will be evaluated by a test pilot. The TIR should contain a compliance
check entry for this section.

         (3) The placard content for older rotorcraft designs is directly related to the
rotorcraft certification basis.  If the rotorcraft type design has an “FAA/AUTHORITY
approved” and segregated Airworthiness Limitations Section of the maintenance
manual, the limitations placard may be revised to comply with the new standard. The
certification basis should be changed in conjunction with the placard change.

AC 27.1561. § 27.1561 SAFETY EQUIPMENT.

     a. Explanation. This standard requires identification or location markings for each
item of safety equipment and operating information for crew-operated controls.

     b. Procedures.

         (1) Release devices, such as levers or latch handles for liferafts and other
safety equipment, should be plainly marked. The method of operation should be
marked also. Stencils, permanent decals, placards, or other permanent labels or
instructions may be used.

         (2) Lockers, compartments, or pouches used to house safety equipment, such
as life vests, should be marked to identify the equipment therein and to also identify, if
not obvious, the method or means of getting to or releasing the equipment.

         (3) Safety equipment labels and instructions should be used.
Section 27.1555(d)(2) concerns emergency control markings. White letters and red
background (or reverse) should be used.

         (4) Locating signs for equipment should be legible in daylight from the
furthest-seated point in the cabin or should be recognizable from a distance equal to the
width of the cabin. Letters, 1 inch high, should be acceptable to satisfy the
recommendation. Operating instructions should be legible from a distance of 30 inches.
These are recommendations based on exit standards of § 29.811(b) and (e)(1).

         (5) Easily recognized or identified and easily accessible safety equipment
located in view of the occupants may not require locating signs, stencils, or decals.
Passenger compartment fire extinguisher in view of the passengers is an example.



                                                       Page G - 31

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →