Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
6/23/23 AC 27-1B, Chg 9
(2) Normal Operating Range. Each normal operating range may be marked
with a green arc or green line that does not extend beyond the maximum and minimum
values for continuous safe operation. Discontinuities in width have been used when
normal ranges vary with other parameters. Integrating instruments in place of these
markings should be encouraged although there may be no regulatory requirement for
them.
(3) Cautionary Ranges. Time limited ranges, precautionary ranges, or ranges
for which special operating procedures are required should be displayed in yellow. If a
yellow range is used to indicate a special operating procedure, information describing
the special procedure should be included in the RFM.
(4) OEI Markings. OEI ratings represent a special challenge for retaining
simplicity and clarity in powerplant instrument markings. OEI ratings are eligible to be
used only during an extremely small portion of total flight time; therefore, they should
not dominate the presentation or obscure other markings. They are needed only for
reference. Indices for 2 ½-minute and 30-minute power may be marked above the
takeoff power redline on engine power instruments. OEI reference markings should be
clearly distinct from the normal all-engines-operating markings. One acceptable means
of marking OEI limits has been narrow dashed radials with yellow for 30-minute and red
for 2 ½-minute limits. OEI markings should be consistent between gauges. For
example, a 30-minute marking on an N1 or torque gauge should be similar in
appearance to the 30-minute marking on the engine temperature gauge.
(5) Red Arcs or Ranges. Sections 27.1549(d) and 27.1553 allow the use of
red indications. Experience has proven that when red arcs are used to indicate
maximum or minimum values, the meaning of a red line loses its significance.
Therefore, the use of red ranges or arcs to indicate limit values should be discouraged.
Red is conventionally used to represent a limit (maximum or minimum) for which an
aircraft or component has been substantiated. A “range” of limits for a given parameter
is not consistent with the definition of the terms “limit,” “minimum,” or “maximum.” In
addition, a red arc tends to imply that more than one value is limiting, that a scale is
provided to show operation within a range of values, and that an absolute limit may not
exist until the extreme of a red range is attained. These implications should be avoided
wherever possible by specifying a single limiting value and marking it with a single red
indication line. If readings in excess of that value were indicated, it would then be
obvious to the crew that a limit had been exceeded. A red arc may be used to indicate a
transient vibration range as indicated in § 27.1549(d); however, if the range is a
cautionary range and not a prohibited range, use of a yellow arc is recommended. The
fuel quantity indicator configuration described in § 27.1553 is considered a special
application of red arcs. Occasionally a red arc has been utilized when limits vary with
other parameters. Discontinuities in width could conceivably represent limits when other
parameters are considered. The use of integrating instruments would alleviate much of
the problem and should be encouraged although there may be no regulatory
requirement for them.
Page G - 25.2
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.