Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
6/23/23 AC 27-1B, Chg 9
AC 27.1543A. §§ 27.1541, 27.1543, 27.1545, AND 27.1549 (AMENDMENT 27-51)
INSTRUMENT MARKINGS: GENERAL.
a. Background and Explanation.
(1) Aircraft instruments have historically been marked in a variety of ways and
with an interesting assortment of symbols. A limited number of regulatory requirements
have been incorporated in part 27, Subpart G, “Markings and Placards,” and these
efforts have standardized some basic aspects of instrument marking for rotorcraft. As
rotorcraft have become increasingly complex with an increased number of engines, OEI
ratings, more sophisticated instrumentation, etc., the need for more specific standards
has greatly increased.
(2) It is vitally important that instrument markings be standardized among
rotorcraft. When markings are not standardized, considerable confusion and additional
workload may be introduced into the cockpit environment. If markings are not standard,
it is conceivable that a marking in one rotorcraft could mean the opposite of a similar
marking in another rotorcraft. The results of such a situation could be troublesome when
pilots fly several rotorcraft models.
(3) The following guidance is offered for the purpose of obtaining a general
standardization of instrument markings. The FAA recognizes that there are a great
many variations in instrument presentations for which all guidance may not apply. This
is particularly true of new designs, such as glass cockpit currently being presented. The
overall philosophies here should be used even if specific guidance is not applicable for
a particular design. Instrument markings are provided to aid interpretation of
instruments quickly and accurately. Good instrument markings should indicate operating
conditions at a glance. The best markings are ordinarily the simplest markings.
b. Procedures.
(1) Limits. Each maximum allowable limit substantiated for safe operation
must be displayed with a red line, as required by § § 27.1545 and 27.1549. This
marking should be a red radial line for circular gauges. If there is a minimum allowable
limit for safe operation, this value should also be marked in red. The use of multiple red
indications should be avoided except where their use is readily apparent to the flight
crewmember. Normally, no more than one maximum and one minimum red indication
should be incorporated on any one instrument to minimize confusion and avoid potential
flightcrew errors; however, use of multiple red indications may be permitted if such
markings can be presented in an acceptable manner.
Page G - 25.1
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.