FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page G-25.3

PDF page 741 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 741
AC 27-1B · G-25.3Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

 6/23/23
                                             AC 27-1B, Chg 9


           (6) Flight Evaluation. In evaluating quantity indicator markings, to meet the
requirements of § 27.1543, the final criterion must be: “Are the markings adequate for
correct interpretation by the crew?” FAA evaluations of quantity indicator markings
should begin early in a certification program utilizing a cockpit or aircraft mock-up
whenever possible. All required quantity indicators and quantity indicator markings must
be readable from each pilot station. Depending on cockpit and window geometry,
quantity indicators should be evaluated in direct sunlight unless they are located high on
the panel underneath a substantial glare shield. Evaluation in direct sunlight is
especially important for any displays using light bars or digital lighting segments, such
as digital radar altimeter presentations or vertical scale instruments using light
segments. Required quantity indicators should be readable without upper body
movement or extensive head movement by the crew. Evaluators should be especially
alert to any scale markings or range markings that are obscured by parallax, since
these features are unacceptable. If the aircraft is to be approved for night operation,
each required indicator must also be evaluated during night lighting conditions, per
§ 27.773. The same visibility requirements apply for night. Except for minor changes,
lighting should be evaluated in flight to correctly evaluate vibration effects and various
background lighting conditions.

         (7) Digital Instruments.


               (i) For purposes of this discussion, the two types of digital indicators
considered are an indicator that consists of a column of light segments that illuminate
sequentially to display changing values, and an indicator that consists of horizontal and
vertical line segments in the configuration of a block “8” to display numerical values.
Both indicator types work well for parameters where trend information is generally not
needed such as engine oil pressure or temperature. However, for rapidly changing
parameters such as engine exhaust gas temperature, torque, or RPM, trend information
may not be attainable. AC 20-88A specifies that instrument markings are intended to
provide necessary information at a glance. Trend information for power indicators is
vitally important for safe operation of a rotorcraft, and this information should be
obtainable at a glance. For the columnar light segments, the ability to quickly detect
trend information is largely a function of the resolution provided by single segments
(e.g., if there are two segments for each percent RPM, the ability to detect trend
information is better than if there is only one segment for each percent RPM). For digital
indicators displaying numerical values, trend information may be unattainable because
rapidly changing parameters produce a blur, and this design may be unsuitable as a
single source of information. The evaluator should use a great deal of caution to ensure
adequate trend information is available in primary power and rotor indicators of digital
design.

                (ii) Another area of concern in digital and moving tape instruments is the
ability to determine when limits are being approached. Color code markings are
frequently incorporated on the moving face of a tape or digital presentation. In such
cases, to meet the requirements of §§ 27.1541(b)(1), 27.1543(b), and 27.1545(a), it is


                           Page G - 25.3

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →