FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page G-23

PDF page 736 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 736
AC 27-1B · G-23Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

3/31/2014                                      AC 27-1B, Chg 4

specifying a single limiting value and marking it with a single red line (radial).  If
readings in excess of that value were indicated, it would then be obvious to the crew
that a limit had been exceeded. A red arc may be used to indicate a transient vibration
range as indicated in § 27.1549(d); however, if the range is a cautionary range and not
a prohibited range, use of a yellow arc is recommended. The fuel quantity indicator
configuration described in § 27.1553 is considered a special application of red arcs.
Occasionally a red arc has been utilized when limits vary with other parameters.
Discontinuities in width could conceivably represent limits when other parameters are
considered. The use of integrating instruments would alleviate much of the problem
and should be encouraged although there may be no regulatory requirement for them.

         (6) Flight Evaluation. In evaluating quantity indicator markings, the final
criterion must be: “Are the markings adequate for correct interpretation by the crew?”
FAA/AUTHORITY evaluations of quantity indicator markings should begin early in a
certification program utilizing a cockpit or aircraft mock-up whenever possible. All
required quantity indicators and quantity indicator markings must be readable from each
pilot station. Depending on cockpit and window geometry, quantity indicators should be
evaluated in direct sunlight unless they are located high on the panel underneath a
substantial glare shield. Evaluation in direct sunlight is especially important for any
displays using light bars or digital lighting segments, such as digital radar altimeter
presentations or vertical scale instruments using light segments. Required quantity
indicators must be readable without upper body movement or extensive head
movement by the crew. Evaluators should be especially alert to any scale markings or
range markings that are obscured by parallax, since these features are unacceptable.  If
the aircraft is to be approved for night operation, each required indicator must also be
evaluated during night lighting conditions. The same visibility requirements apply for
night. Except for minor changes, lighting should be evaluated in flight to correctly
evaluate vibration effects and various background lighting conditions.

         (7) Digital Instruments.

                  (i) For purposes of this discussion, the two types of digital indicators
considered are an indicator which consists of a column of light segments which
illuminate sequentially to display changing values, and an indicator which consists of
horizontal and vertical line segments in the configuration of a block “8” to display
numerical values. Both indicator types work well for parameters where trend
information is generally not needed such as engine oil pressure or temperature.
However, for rapidly changing parameters such as engine exhaust gas temperature,
torque, or RPM, trend information may not be attainable. AC 20-88A specifies that
instrument markings are intended to provide necessary information at a glance. Trend
information for power indicators is vitally important for safe operation of a rotorcraft, and
this information must be obtainable at a glance. For the columnar light segments, the
ability to quickly detect trend information is largely a function of the resolution provided
by single segments (e.g., if there are two segments for each percent RPM, the ability to
detect trend information is better than if there is only one segment for each percent
RPM). For digital indicators displaying numerical values, trend information may be


                                                          Page G - 23

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →