FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page G-24

PDF page 737 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 737
AC 27-1B · G-24Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 4                                                     3/31/2014

unattainable because rapidly changing parameters produce a blur, and this design may
be unsuitable as a single source of information. The evaluator should use a great deal
of caution to ensure adequate trend information is available in primary power and rotor
indicators of digital design.

                   (ii) Another area of concern in digital and moving tape instruments is the
ability to determine when limits are being approached. Color code markings are
frequently incorporated on the moving face of a tape or digital presentation. In such
cases, it is mandatory that limit markings be affixed adjacent to the presentation, or that
another means be provided so that the pilot can anticipate approaching a limit. The
beginning and end of normal and cautionary ranges should be marked adjacent to the
display. The entire range need not be color coded adjacent to the display if the colors
are integral on the face of the tape or in the individual digital segments. Marking of limit
values solely on the tape or in the colored light segments alone is unsatisfactory.
Marking of digital indicators displaying numerical values is adequately addressed in
AC 20-88A, paragraph 6.

                    (iii) Appropriate failure modes should be evaluated during the system
analysis. This will ordinarily include portions of the digital display. Such failures should
be detectable whenever they affect reading accuracy. As a result of this analysis, the
system may incorporate a test feature that ensures all digital segments operate
satisfactorily. This feature should be encouraged.

         (8) Additional Markings. To keep markings standardized and uncomplicated,
only the FAA/AUTHORITY-approved ranges and limits should be included. Items such
as manufacturer’s recommended values or manufacturer’s warranty information are
inappropriate for instrument markings and should not be included. Such information
may be presented elsewhere. Transient limits may be indicated by a small red index
such as a dot or triangle. Information defining allowable conditions for each transient
index should be in the RFM (e.g., maximum for starting - 12 seconds).

         (9) Airspeed Indicator. While the foregoing information is generally applicable
to airspeed indicators, some particular features warrant additional attention.

                  (i) A red cross-hatched radial line should be located at power-off VNE if that
value is less than power-on VNE.

                   (ii) Many rotorcraft have erratic, unreliable, or nonrepeatable airspeed
indications at low speed which warrant caution when operating in that speed range. In
such cases, a yellow arc on the instrument with an appropriate flight manual explanation
has been found acceptable.

                    (iii) Indicated airspeed values should be utilized for all airspeed indicator
markings.




Page G - 24

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →