Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
2/12/03 AC 27-1B, Chg 1
(iv) Service experience may dictate additional and subsequent (to type
certification) changes to the airworthiness limitations section. ADs may be used to
revise the limitations. (The relationship between ADs and the process of changing the
limitations is covered in the preamble of Amendment 27-4 (33 FR 14104;
September 18, 1968.) Whenever the revised limitations are made restrictive for aircraft
in service, the Administrative Procedures Act requires “notice and public procedure” to
persons that may be affected and to satisfy the requirement for notification of the
changes and identification of the correct issue of the airworthiness limitations, if
appropriate. This procedure is also used for restrictive or reduced operation limitations
in the RFM.
b. How to Prepare Instructions for Continued Airworthiness
(1) Explanation. The FAA/AUTHORITY recognized the need for Instructions
for Continued Airworthiness to maintain the rotorcraft in an airworthy condition.
(i) Amendment 27-18, 45 FR 60177, September 11,1980, states the
applicant must prepare Instructions for Continued Airworthiness, in accordance with
Appendix A of this part, that are acceptable to the Administrator.
(ii) Section 21.50(b), Amendment 21-51, 45 FR 60170, September 11, 1980,
requires the holder of a design approval to furnish at least one set of complete
Instructions for Continued Airworthiness prepared in accordance with § 27.1529 of this
chapter. The design approval can include either the type certificate or supplemental
type certificate for an aircraft or aircraft engine for which application was made after
January 28, 1981. The approved and accepted set of complete Instructions for
Continued Airworthiness should be furnished upon delivery or upon issuance of the first
standard airworthiness certificate for the affected aircraft, whichever occurs later.
(iii) The ICAs or ICA supplements are also required for PMAs, major
design change, or alteration approvals that the existing ICAs do not adequately cover.
In such instances, it is the responsibility of the PMA holder, or the person who receives
the design change or alteration approval to produce the required ICAs and distribute
them in accordance with the requirements of § 21.50(b). The acceptance for these
ICAs or supplements should follow the procedure in Section b(2).
(2) Procedure
(i) General. When the rule requires Instructions for Continued
Airworthiness for a rotorcraft, its rotors, and appliances, the applicant must prepare
Instructions for Continued Airworthiness in accordance with Appendix A to FAR/JAR
Part 27, that are acceptable to the FAA/AUTHORITY.
(ii) Guidance. The FAA/AUTHORITY has guidance material to assist an
applicant in preparing Instructions for Continued Airworthiness for the type design
change. AC 27-1B, Appendix A, provides a detailed template describing the
Page G - 19
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.