FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page G-18

PDF page 731 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 731
AC 27-1B · G-18Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 1                                                           2/12/03

              (B) The airworthiness limitations section contains information derived
primarily but not solely from the data approved under § 27.571. In addition to
replacement times and inspections, where appropriate, some of the basic usage
assumptions made in the fatigue evaluation, which the operator can reliably assess
(such as numbers of ground-air-ground cycles) should be identified. These should be
noted in the airworthiness limitations so that the operator may take appropriate action
(see MG 8 and MG 11). Approval of this section of the manual (draft form is
acceptable) must be accomplished before type certification. See Part 27, Appendix A,
paragraph A27.4 of Amendment 27-17. (For further information, see comments for
Proposal 8-25, § XX.4, in the preamble of Amendment 27-18 (45 FR 60154,
September 11, 1980).)

             (C) Part 27, Appendix A, paragraphs A27.3(a) and (b) pertain to the
content of the instructions for continued airworthiness. For example, scheduling and
servicing information is included in this section of the manual.

                   (ii)    Identifying and Serializing Fatigue Critical Components.

              (A) Part numbers and serial numbers must be applied to fatigue critical
components as noted in § 45.14 and § 27.1529(a)(1) and (2). Electric arc marking
method should not be used due to possible internal arcing, pitting of surfaces, and
changes in physical or chemical characteristics due to the local high temperature at the
arcs.

              (B) Vibrating pencils, name plates, or permanent inks may be used.
However, serial numbers should be applied on each part such that material is upset or
displaced on the part, thereby attaining a more permanent number. When material is
upset or displaced, the component's integrity and fatigue tolerance must not be
compromised, for example, the least critical or lowest stressed area should be used.

             (C) For small parts, the rule (§ 45.14) allows markings that are equivalent
to part and serial numbers. Markings or symbols may be used to enable the
identification of a part as one for which a replacement time, inspection interval, or
related procedure is specified in the airworthiness limitations section. The
FAA/AUTHORITY-stated identification of such small parts is clearly essential for safety
and may not be relieved. With adoption of Amendment 27-18, the marking
requirements are contained in § 45.14, Amendment 45-12.

                    (iii)  A draft copy of the manual should be available to the
FAA/AUTHORITY for use during the F&R program if such a program is conducted
under § 21.35(b). The content of the manual may be limited to the information
necessary to maintain the aircraft during the F&R program. The manual must be
completed and furnished with each aircraft receiving an airworthiness certificate,
§ 21.50(a) and (b).




Page G - 18

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →