FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page G-17

PDF page 730 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 730
AC 27-1B · G-17Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/12/03                                        AC 27-1B, Chg 1

approval of the fatigue characteristics of critical flight structure.” Refer to FAA
Order 8620.2, Applicability and Enforcement of Manufacturer’s Data,
November 2, 1978, for further information.

                   (ii)    Critical components must be identified by part number (or equivalent)
and serial number (or equivalent). Section 27.1529(a)(1) and (2) of Amendment 27-3
and/or § 45.14 list the requirements. The part numbers of parts and/or components
requiring inspections and/or replacement as a result of § 27.571 must be listed in the
airworthiness limitations section of the manual or another separate, segregated section
of the manual appropriate to the rules.

                    (iii)   Rotorcraft type designs are unique in comparison to airplane designs
in that transmissions and rotors and some elements of flight control systems have
critical components that may be adversely affected by operating conditions and time in
service. The FAA/AUTHORITY-approved airworthiness limitations section may include
such items as gear sets, bearings, etc., of the rotorcraft type design if a finite life was
established during the type certification program and/or if the FAA/AUTHORITY
determined that mandatory inspections and/or replacement of the component (part) was
necessary to maintain airworthiness of the rotorcraft. For example, a drive spline, gear,
or bearing was serviceable after concluding the ground endurance test and/or
FAA/AUTHORITY flight test program. However, an FAA/AUTHORITY-mandated
inspection or replacement of the component was considered essential for airworthiness
of the rotorcraft type design and necessary for type certification. Time between
overhaul (TBO) of components is not part of the airworthiness limitations but is a
recommendation from the manufacturer (See Part 27, Appendix A, A27.3(b)(1)).  If an
inspection or replacement of a part in an assembly is required, the inspection interval or
replacement time and the part number should be included in the limitations. The
inspection interval or replacement time may or may not coincide with the recommended
overhaul interval of the assembly. (See the comments for Proposal 8-25, § XX.4 in the
preamble of Amendment 27-20 (45 FR 60154), September 11, 1980). Note that parts
considered unserviceable at the conclusion of the ground endurance test of § 27.923
are not acceptable for type certification.

         (2) Procedures.

                  (i)    General.

              (A) The rule states that the manual must contain all information that the
applicant considers essential for proper maintenance. Amendment 27-3 added the
requirement for an airworthiness limitations section and Amendment 27-18 revised
§ 27.1529 and added Appendix A that contains the requirements for preparation of the
manual. The airworthiness limitations section of the manual, and any revisions thereto,
must be FAA/AUTHORITY approved. The manufacturer’s recommendations for
continued airworthiness are not FAA/AUTHORITY approved.




                                                       Page G - 17

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →