Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
its predictive validity, sensitivity, reliability, applicability to the particular cockpit
configuration, and availability of a suitable reference for comparison.
(2) Analytical Approach.
(i) One analytical approach defines workload as a percentage of the time
available to perform tasks (Time Line Analysis). This process may be applied to an
appropriate set of flight segments in which operationally important time constraints can
be identified. This method is useful for evaluation of cockpit changes relating to overt
pilot work such as control movements and data inputs. The generally accepted practice
involves careful selection of the limited set of flight scenarios and time segments that
represent the range of operational requirements (including the range of normal and
non-normal procedures.) Time line analysis yields useful data when tasks must be
performed within operationally significant time constraints. The adequacy of this
method is very much dependent on an accurate determination of the time available.
Absolute standards are not available for interpretation of obtained time required scores,
but such records can be used to identify high or simultaneous workload demands for
later testing in a simulator or aircraft, and comparisons can be made with overt workload
demands in proven aircraft. However, the impact of cockpit changes on planning and
decision-making is difficult to quantify by this method.
(ii) The most frequently used basis for deciding that a new design is
acceptable is a comparison of a new design with previous designs proven in operational
service. By making specific evaluations using the acceptable human factors
techniques, and comparing new designs to a known baseline, it is possible to proceed
with confidence that the changes incorporated in the new designs accomplish the
intended result. When the new cockpit is considered, certain components may be
proposed as replacements for conventional items, and some degree of rearrangement
may be contemplated. New avionics systems may need to be fitted into existing panels,
and newly automated systems may replace current indicators and controls. As a result
of this evolutionary characteristic of the cockpit design process, there is frequently a
reference cockpit design, which is usually a conventional aircraft that has been through
the test of operational usage. If the new design represents an evolution, improvement
attempt, or other deviation from this reference cockpit, the potential exists to make
direct comparisons. Service experience should be researched to assure that any
existing problems are understood and not perpetuated.
(iii) If preliminary analyses by the certification team identify potential
problem areas, these areas should receive more extensive evaluation and data
collection in order to verify compliance with § 27.1523. These concerns should be
adequately addressed in the manufacturer’s demonstration plan when submitted to the
FAA/AUTHORITY.
(iv) If the new design represents a significant change in level of
automation or pilot duties, analytic comparison to a reference design may have
lessened value. Without a firm data base on the time required to accomplish both
Page G - 13
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.