FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page G-12

PDF page 725 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 725
AC 27-1B · G-12Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

         (3) Minimum crew requirements for the same type design may vary with the
kind of operation. Many rotorcraft have been approved for a single-pilot crew for visual
flight rules (VFR) operations but require a two-pilot crew for IFR operations. Other kinds
of operations that may require more than one crewmember to meet type certification
requirements are night operations, operations into known icing conditions, operations in
falling and blowing snow, extended overwater operations, and external load operations.

         (4) It is important to distinguish between the minimum crew requirements for
compliance with Part 27 type certification regulations and the minimum crew
requirements of the various operating regulations (Parts 61, 91, 121, 133, 135, and
137). A rotorcraft may be type certified for a minimum crew of one and still be required
to have a crew of two or more by the operating regulations for certain types of operation
or by the workload associated with an operating environment. Therefore, an applicant
should carefully consider the possible operational uses of any rotorcraft design and
become familiar with the applicable operating regulations as well as the type
certification requirements early in the design process.

         (5) Although the rotorcraft configuration is typically certified with the
pilot-in-command station in the right seat, the left seat may be used for the
pilot-in-command if, in addition to the flight controls required to control the rotorcraft, the
following are included for the pilot: throttle control including ability to shut down all
engines, airspeed indication, altitude indication, rotor and engine RPM, and engine
torque and exhaust gas temperature. The authority should evaluate a change to the
pilot-in-command station.

         (6) The applicant is encouraged to contact the responsible type certification
office as early in the design phase as possible to initiate the qualitative assessment
process. Cockpit layout drawings, instrument panel mockups, and full-scale cockpit
mockups can be used to determine if required controls are accessible and to begin the
pilot workload assessment for certain operations.

     b. Procedures.

         (1) General.

                  (i)   A systematic evaluation and test plan is required for any new or
modified rotorcraft. The methods for showing compliance should emphasize the use of
acceptable analytical, simulation, and flight test techniques. The crew complement
should be studied through a logical process of estimating, measuring, and then
demonstrating the workload imposed by a particular cockpit design. When the minimum
crew requirements have been determined, they should be included in the limitations
section of the Rotorcraft Flight Manual in accordance with § 27.1583(d).

                   (ii)   Appropriate analysis should be conducted by the applicant early in the
design process. The specific method(s) of analysis should be selected on the basis of



Page G - 12

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →