FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page G-11

PDF page 724 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 724
AC 27-1B · G-11Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

30-second and 2-minute power ratings using terminology similar to that developed for
the 2½-minute and 30-minute power ratings. Additionally, these paragraphs require the
ability to detect any damage which occurs due to the use of either 30-second or
2-minute OEI limits and requires that the procedures to inspect for such damage be
provided in the instructions for continued airworthiness for either the engine and/or the
airframe.

     b. Procedures. All of the policy material pertaining to this section remains in
effect. Additionally, the following procedures should be considered:

Sections 27.1521(j) and (k) require limitations for 30-second/2-minute OEI operation for
multi-turbine engine powered rotorcraft. The same parameters required for the takeoff
and continuous ratings should be established as limitations for each approved OEI
rating (i.e., maximum rotational speed, time, gas temperature, and torque). These new
ratings can only be approved as a rating in conjunction with the other. That is, a
rotorcraft with a 30-second OEI rating must also have a 2-minute OEI rating and
vice-versa. The 30-second and 2-minute OEI ratings are also limited to use for
continued operation of the remaining engine(s) upon failure or precautionary shutdown
of an engine. Upon the use of 30-second or 2-minute OEI ratings an inspection for
damage to the airframe and/or engine may need to be conducted. The inspection
should be accomplished per the procedures furnished by the airframe and engine
manufacturers and any damage occurring due to the use of these new ratings should be
detected using these inspection procedures. Section 27.923 includes requirements for
qualification of the rotor drive system for 30-second and 2-minute OEI powers.
Section 27.1501(a) requires that information necessary for safe operation should be
established as limitations. The limitation information provided in this paragraph should
be provided in the flight manual. This includes a possible requirement for an inspection
prior to further flight after the use of either 30-second or 2-minute OEI rating.

AC 27.1523. § 27.1523 MINIMUM FLIGHTCREW.

     a. Explanation.

         (1) This rule requires that the minimum crew necessary to show compliance
with the requirements of Part 27 or for safe operation of the rotorcraft be established as
an operating limitation.

         (2) The determination of minimum crew requirements is typically based on a
subjective pilot assessment of the crew requirements for safe operation of each
rotorcraft design. Certain regulations, such as the requirements for instrument flight
rules (IFR), have specific quantitative differences between single-pilot and two-pilot
requirements. However, most often the minimum crew requirement will be based on
more subjective considerations such as location of necessary controls, pilot workload to
accomplish required tasks, type of operation, and overall complexity of the rotorcraft
design.



                                                       Page G - 11

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →