FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page G-9

PDF page 722 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 722
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

outside approved limits, special interior placarding or cautionary information should be
provided in appropriate sections of the RFM.

AC 27.1521. § 27.1521 (Amendment 27-14) POWERPLANT LIMITATIONS.

     a. Explanation.

         (1) This rule requires that the various parameters and operating conditions
listed under each type of powerplant operation be evaluated and established as
operating limitations. The procedures for establishing and verifying each powerplant
limitation are discussed in the powerplant section of this AC. This rule requires that
powerplant limitations be established for two specific types of operation or power
ratings; takeoff and continuous. Additional limitations are required to account for engine
and transmission cooling and minimum required fuel grade.

         (2) Paragraph (e) requires that for turboshaft engines, a limit engine torque be
established in addition to the other limiting parameters listed under each type of
operation in paragraphs (b) and (c). Compliance with this paragraph requires that a
torque limit be established for each approved engine rating (i.e., takeoff, continuous,
etc.) even though not specifically stated in the rule.

         (3) For rotorcraft equipped with two or more turboshaft engines and seeking
approval for one-engine-inoperative (OEI) ratings, the same parameters required for the
takeoff and continuous ratings should be established as limitations for each approved
OEI rating (i.e., maximum rotational speed, time, gas temperature, and torque).
Section 27.923 includes requirements for qualification of the rotor drive system for
2½-minute and 30-minute OEI powers. Section 27.1501(a) requires that any
information necessary for safe operation must be established as limitations. Thus the
establishment of OEI powerplant limitations is required even though not specifically
addressed in § 27.1521 (through Amendment 27-14).

         (4) It is important to differentiate between the rotorcraft powerplant limitations
and the engine limitations as established under Part 33. For some parameters, these
two limits may be identical, but frequently the engines will be capable of exceeding the
maximum limitations substantiated for the combined powerplant installation. Limitations
established according to this rule may not exceed the engine limitations established in
accordance with Part 33 but may be less than the Part 33 limits as desired by the
applicant.

     b. Procedures.

         (1) Determine the limiting parameters for each required power rating according
to the requirements of Part 27, Subpart E, Powerplant. (See applicable paragraphs of
this AC for detailed procedures.)




                                                        Page G - 9

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →