Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
achieved. It may be difficult to obtain minimum power-off RPM prior to encountering
retreating blade stall at combinations of high weight, high collective pitch, low rotor
speed, and high forward speed. In this case VNE (power-off) can either be decreased in
accordance with § 27.1505(c) or the low RPM range can be evaluated in a transient
manner during engine failure testing at high speed. Any condition in which blade stall is
suspected should, of course, be investigated with a great deal of caution and build-up
testing is recommended. The transient low RPM limit for power-off landings may be
tested only during actual power-off landings. In that case, the 5 percent margin is not
required.
(2) Testing for suitable minimum and maximum power-on RPM values may be
conducted during the designated FAA/AUTHORITY flight test program. The combined
engine and governor response must allow accomplishment of all appropriate flight
maneuvers without exceeding minimum or maximum power-on rotor limits. As in the
power-off case, appropriate transient ranges and limits may be approved when properly
substantiated. Transient ranges should be evaluated using similar methods and
techniques to those described above. Power-on RPM determination must include not
only rotor system considerations but engine and drive system characteristics as well. It
is important to remember that all power-on ranges must be eligible under the Part 33
engine approval and that the power-off range must include adequate margins from
potentially hazardous drive system phenomena, such as drive shaft whirl modes.
AC 27.1519. 27.1519 (Amendment 27-21) WEIGHT AND CENTER OF GRAVITY.
a. Explanation. This rule requires that weight and center of gravity (CG)
combinations which are substantiated structurally and also found satisfactory during
flight tests (per §§ 27.25 and 27.27) must be established as operating limits. A related
portion in § 27.1583(c) further requires that weight and CG limitations be entered in the
RFM limitations section. Both maximum and minimum weight must be established as
operating limitations along with the corresponding longitudinal and lateral centers of
gravity for each condition. Weight and CG limits are discussed in more detail in
paragraphs AC 27.25 and AC 27.27 of this AC.
b. Procedures.
(1) The results of shifts in center of gravity with fuel burn should be evaluated.
If it is possible to take off within the approved loading envelope and subsequently burn
fuel to a condition which is significantly beyond the approved weight/CG envelope, then
there should be appropriate instructions in the loading and/or operating procedures of
the RFM to avoid this condition.
(2) Typical loading conditions should not result in weight/CG combinations
outside of approved limits. A minimum of two loadings, appropriate to the rotorcraft
configuration, should be evaluated. These should include critical combinations of
maximum/minimum variables for fuel, passengers, and crew. If this results in loading
Page G - 8
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.