FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page G-7

PDF page 720 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 720
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

forces on the blades are at their highest and stress levels on rotating components such
as blade grips may be critical.  If a particular model has a very large weight spread
between minimum and maximum gross weights, the applicant may elect to specify two
ranges of power-off RPM dependent upon weight. This may be needed to ensure
adequate power-off rotor RPM with collective full down without requiring the very low
power-off rotor speeds at maximum weight, a condition which would be inappropriate for
operation of the rotorcraft in service. Transient power-off RPM ranges may also be
approved if needed for engine failure conditions; however, these transients must also be
substantiated structurally and in flight.

         (3) Power-on Limits. The minimum power-on rotor speed must be established
so that it is no less than the minimum rotor speed that has been established structurally.
The minimum power-on speed also cannot be less than those values achieved during
any of the critical maneuvers during flight test substantiation of the rotorcraft. A
5 percent margin between the substantiated value and the limit value is not required as
in the power-off case. This rule also makes reference to § 27.33(a)(1) and (b)(1) for
establishing the minimum power-on value. The reference to paragraph (a)(1) is
intended to ensure that the minimum power-on RPM value is low enough to
accommodate the RPM values which will occur as a result of power changes and flight
maneuvers expected in service. The reference to (b)(1) establishes the requirement
that the minimum power-on RPM can not be greater than the minimum RPM used to
determine the appropriate setting of the main rotor high pitch stop. Although the
maximum power-on value is not specifically referred to in this section, it must be
established as a limitation per § 27.309. In addition, for compliance with the
requirements of § 27.141(b) regarding smooth transition from power-on to power-off
flight, the power-on maximum limit should not be greater than the power-off maximum
limit and the power-on minimum limit should not be less than the power-off minimum
limit.

         (4) Transient Limits. Transient limits must be substantiated and approved in a
similar manner. Transient limits may be outside of the steady state “red-line” limits.

     b. Procedures.

         (1) Tests for substantiation of stress and vibration at the 5 percent underspeed
and overspeed conditions in autorotation are ordinarily conducted as a part of the flight
strain survey. For purposes of finding compliance with this rule, it is suggested that as a
minimum, FAA/AUTHORITY certification personnel witness applicable portions of the
test program and monitor telemetry or flight recorded data, as necessary, to verify
compliance with this rule. Tests at maximum weight and at a relatively light weight
condition are normally sufficient. Tests must be conducted at speeds up to VNE
(power-off) at 105 percent of maximum RPM and 95 percent of minimum RPM.  It is
also appropriate to investigate speeds to 1.1 VNE (power-off) at maximum and minimum
power-off RPM values. The normal low pitch stop may need to be downrigged in order
to achieve the high RPM values at high speed. This feature should be coordinated with
the manufacturer prior to the flight strain survey to ensure necessary conditions are


                                                        Page G - 7

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →