FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page G-6

PDF page 719 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 719
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

         (3) Power-off Limits. A power-off VNE may be established either by design or
flight test and should be substantiated by flight tests. A power-off VNE is generally
required if the handling qualities or stability characteristics at high speed in autorotation
are not acceptable. A limitation of the power-off VNE may also be used if the rotorcraft
has undesirable or objectionable flying qualities, such as large lateral-directional
oscillations, at high autorotational airspeeds. The power-off VNE must meet the same
criteria for control margins as the power-on VNE. The regulation requires that the
power-off VNE be no less than the speed midway between the power-on VNE and the
speed used to comply with the rate of climb requirements for the rotorcraft. When the
regulation was written, rotorcraft VNE speeds were significantly lower than those of
recently certificated rotorcraft. The high VNE speeds of current rotorcraft result in
relatively high values for power-off VNE. Speeds lower than those specified in the
regulation have been found acceptable through a finding of equivalent safety if the
selected power-off VNE is equal to or greater than the power-off speed for best range. In
any case, the power-off VNE must be a high enough speed to be practical. A
demonstration is required of the deceleration from the power-on VNE or OEI VNE to the
power-off VNE. The transition must be made in a controlled manner with normal pilot
reaction and skill.

     b. Procedures. The tests to substantiate the different VNE speeds are ordinarily
conducted during the flight characteristics flight tests. The flight test procedures are
discussed for the various limiting areas in earlier paragraphs of this document. Static
stability test techniques are covered in paragraph AC 27.175 and the vibration test
techniques in paragraph AC 27.251.

AC 27.1509. § 27.1509 ROTOR SPEED.

     a. Explanation.

         (1) General. This rule requires minimum and maximum power-off rotor speeds
to be established as operating limitations.  It also specifies the appropriate margins
below and above these limits that must be substantiated structurally and by flight tests.
In addition to addressing power-off limits, the rule requires that minimum power-on RPM
be established as an operating limit, and it specifies conditions, by reference, for
establishing a minimum appropriate power-on speed.

         (2) Power-off Limits. The power-off or autorotational RPM limits are
established by design and substantiated by structural testing. Limits are confirmed
during flight testing. Critical components must be designed for RPM values at least
5 percent above and below the maximum and minimum approved RPM values
respectively. This 5 percent conservative speed requirement is in addition to the other
structural safety factors built into the design requirements. A transient limit lower than
the minimum in-flight RPM (power-off) will be defined to cover the final phase of a total
power-off landing. Maximum weight is ordinarily critical for both tests. At low RPM,
high coning angles can produce high stress levels in blade bending. Large flapping
angles or controllability problems may also develop. At high RPM values, centrifugal


Page G - 6

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →