FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page G-4

PDF page 717 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 717
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 1                                                           2/12/03

AC 27.1505. § 27.1505 (Amendment 27-21) NEVER-EXCEED SPEED.

     a. Explanation.

         (1) General. This rule requires the never-exceed speed (VNE) for both
power-on and power-off flight to be established as operating limitations. The rule
specifies how to establish and substantiate these limits.

         (2) Power-on Limit.

                  (i)   The all-engines-operating VNE is established by design and
substantiated by flight tests. The VNE limits are the most conservative value that
demonstrates compliance with the structural requirements (§ 27.309), the
maneuverability and controllability requirements (§ 27.143), the stability requirements
(§§ 27.173 and 27.175), or the vibration requirements (§ 27.251). The power-on VNE
will normally decrease as density altitude or weight increases. A variation in rotor speed
may also require a variation in the VNE. The regulation restricts to two the number of
variables that are used to determine the VNE at any given time so that a single pilot can
readily ascertain the correct VNE for his flight condition with a minimum of mental effort.
Helicopter manufacturers have typically presented never-exceed-speed limitation data
as a function of pressure altitude and temperature. This information was placarded as
well as contained in the flight manual. As the weight of some derivative models was
increased, the FAA/AUTHORITY accepted altitude/temperature/VNE limitations that
were categorized or contained within a weight range. Literal compliance with the
regulation then required that the takeoff weight be calculated and then the indicated,
appropriate airspeed limitation chart or placard be used for the entire flight. However
VNE charts or placards based on longitudinal center-of-gravity (c.g.) have been found to
be unacceptable, since the same chart would potentially not be used throughout the
flight and the pilot would thus be dealing with more than two variables to determine VNE.
Alternatively, rotorcraft that are equipped with air data computers or other similar
equipment are allowed to vary as many parameters as desired, if the final results are no
more than two parameters that define the VNE displayed to the pilot in an unambiguous
manner. These rotorcraft must also have a method for determining VNE that complies
with the regulation in the event the air data computer system fails. This method is
usually more conservative than the automatic system because of the limitation in the
number of parameters that can be varied.

                   (ii)   To ensure compliance with the structural requirements (§ 27.309),
vibration requirements (§ 27.251), and flutter requirements (§ 27.629), the
all-engines-operating VNE should be restricted so that the maximum demonstrated main
rotor tip Mach number will not be exceeded at 1.11 VNE for any approved combination of
altitude and ambient temperature. Previous rotorcraft cold weather tests have shown
that the rotor system may exhibit several undesirable and possibly hazardous
characteristics due to compressibility effects at high advancing blade tip Mach numbers.
As the center of pressure of the advancing rotor blade moves aft near the blade tip due
to the formation of localized upper surface shock waves, rotor system loads may


Page G - 4

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →