FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page G-3

PDF page 716 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 716
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B


             (C) Fly-by-Wire Elevator Systems (FBW).

             (D) Air Data Computer Systems (ADC).

         (2) Groundspeed Limitations. Although not specifically required by this
“airspeed limitations” regulation, it may be necessary to establish “groundspeed”
limitations for wheel-gear-equipped rotorcraft and maximum landing touchdown
groundspeeds for utility type, float-gear-equipped rotorcraft. These wheel gear
limitations are required to show compliance with the ground-handling characteristic
requirements, structural strength requirements, or the ground-loads requirements.
However because of the operational similarity of groundspeed limits to airspeed limits, it
is a common practice to include groundspeed limitations under the airspeed limitations
heading in the flight manual. For this reason, groundspeed limitations are included in
this paragraph of the AC. Groundspeed limitations should be established with adequate
safety margins to account for the possible inaccuracies associated with the necessity for
the pilot to estimate groundspeed from indicated airspeed and available wind speed and
direction information during actual operations. The following are examples of
groundspeed limitations that have been required during past type certification programs:

                  (i)   Maximum Groundspeed for Takeoff or Landing. The maximum
acceptable groundspeed that can safely be used for wheel gear equipped rotorcraft
takeoff and landing maneuvers should be determined based on landing gear limitations
or ground controllability limitations. This speed should be fast enough to account for
landing touchdown speeds at the maximum approved density altitude for normal takeoff
and landing.

                   (ii)  Maximum Groundspeed for Brake Application. The maximum speed
at which the wheel brakes may be applied without exceeding maximum brake energy
capabilities should be determined for wheel equipped rotorcraft. This speed should be
verified by test throughout the approved takeoff and landing envelope of the rotorcraft.
The critical combination of gross weight and density altitude for brake energy
considerations may be determined by analysis to minimize the required amount of
testing. The maximum brake application groundspeed should be high enough to
encompass brake application during landing at the maximum approved density altitude.

                    (iii)   Other Groundspeed Limitations. For some rotorcraft designs with skid
type landing gear, it may be necessary to establish a maximum landing touchdown
speed for normal operations to comply with structural requirements. Optional
equipment configurations such as float equipment, skis, etc., which are attached to
conventional landing gear skids may require maximum landing groundspeed limits that
are less than the limit for the basic rotorcraft. Rather than limitations, operational
information may be sufficient for skid type landing gear and for utility or float landing
gear.




                                                        Page G - 3

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →