FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page F-102

PDF page 711 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 711
AC 27-1B · F-102Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

presented to the first pilot via the required flight instruments. This correlation should
normally be established before flight, and should have an accuracy rate that does not
diverge by more than 4 minutes and 4 seconds in 8 hours.

               (vi)  Caveat.  It should be noted that even though the requirements
outlined above provide for compliance with the specific provisions of § 27.1459
regarding the acquired data and its accuracy, a flight recorder certified to these
minimum standards will not meet the requirements of Appendix F of FAR 91 or
Appendix C of FAR 135.  If the flight recorder is to be used to comply with these
operating rules, it is recommended that the appropriate appendix be consulted prior to
requesting certification. The approved configuration may then be certified as meeting
the requirements of the appropriate appendix.

         (3) Flight Recorder Mechanical Installation. The non-ejectable flight recorder or
the portion thereof which contains the recorded data should be physically located to
enhance the probability of the recording surviving a crash. Normally, such a location
would be in the lower portion of the rotorcraft as far aft as possible. However, other
locations in the rotorcraft may be suitable to meet the requirement to “minimize the
probability of container rupture resulting from crash impact and subsequent damage to
the record from fire.” The normal accelerometer should be located within the most
restrictive center of gravity of the rotorcraft. The required underwater locator is usually
mounted to the case of the flight recorder.

         (4) Electrical Power Supply. The rule requires that the flight recorder should be
supplied with power from the most reliable source that does not jeopardize essential or
emergency loads. Since the functioning of the flight recorder is required by operating
rules for some operations, it should be given priority over other nonessential loads.

         (5) Self-Test Function. The flight recorder should be provided with a preflight
test that will provide confirmation that the recorder and its recording medium are
functioning properly.

         (6) Data Erasure Feature.  If this function is provided and the flight recorder is
not powered solely by an engine or transmission driven generator, the installation
should provide the following features:

                  (i)   Any probable malfunction will not cause erasure of the recording
medium.

                   (ii)   The crash impact forces will not cause activation of the data erasure
function.

                    (iii)   Inadvertent actuation of the data erasure function is minimized.
Usually, this is accomplished by requiring two separate actions to operate the data
erasure.



Page F - 102

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →