FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page F-103

PDF page 712 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 712
AC 27-1B · F-103Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

AC 27.1461. § 27.1461 (Amendment 27-2) EQUIPMENT CONTAINING HIGH
         ENERGY ROTORS.

     a. Explanation. This section contains requirements for the installation of
equipment containing high energy rotors. A high energy rotor is any rotor that has
sufficient kinetic energy to cause damage to surrounding structure, wiring, and
equipment if a failure occurs. Turboshaft engine and APU rotors are not covered by this
paragraph. One of the following requirements of § 27.1461 must be met.

         (1) Paragraph (b) deals with damage tolerance, containment, and control
devices.

         (2) Paragraph (c) deals with containment and inoperative speed controls.

         (3) Paragraph (d) deals primarily with equipment location.

     b. Procedures.

         (1) Compliance with § 27.1461(b) can be shown by a combination of analysis
and test. A failure modes and effects and a stress analysis, together with a dynamic
test, could be used to verify that the rotor would withstand the damage from
environmental effects, and that the rotor case would contain any parts that may
separate from the rotorshaft. The analysis and test should include a demonstration of
the control device’s ability to prevent limitations from being exceeded.

         (2) If compliance with the requirements of § 27.1461(c) is chosen, a test must
be conducted which demonstrates that all parts from any type failure of a high energy
rotor will be contained when that rotor is operating at the highest speed obtainable, with
all speed control devices inoperative. This containment should not damage any
components, systems, or surrounding structures that are essential for continued safe
flight.

         (3) If compliance with § 27.1461(d) is chosen, the location of the high energy
rotor must be in an area where uncontained failed parts will not damage other
components, systems, or surrounding structure which are essential for continued safe
flight.  It must also be shown that there is no possibility for failed, uncontained parts to
enter the cabin area and endanger any occupant.





                                                      Page F - 103

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →