FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page F-99

PDF page 708 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 708
AC 27-1B · F-99Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

         (1) Individual components should be substantiated by either a vendor’s or a
primary manufacturer’s laboratory test reports. These tests should establish
performance ratings such as pressures, flow rates, environmental capability, etc., to be
approved.

         (2) After the total system is installed, ground tests should be conducted to
ensure the system performs as intended and that each component is functioning within
its design rating. System testing should consider the provisions of § 27.1435(b).

         (3) If the total system design permits each combined independent power
source and actuator to be disabled by shutoff valves, engine shutdown, etc., each
combination should be disabled and the remaining combination verified to perform the
necessary control functions. The test should be accomplished again with the
functioning combination disabled and the disabled combination functioning. These tests
should be accomplished first by ground tests, then repeated in flight.

         (4) Temperature and pressure instrumentation should be provided at the critical
points in the system. Temperature results should be corrected for hot day conditions.
(Paragraph AC 27.1309b(2)(i) gives a recommended procedure.)

         (5) All controls should be cycled throughout their complete range of travel while
accomplishing the provisions of paragraph d(2) above.

         (6) Satisfactory hydraulic system performance should be verified while the
pump drive sources (rotor, engine, etc.) are individually varied throughout their
approved operating range.

         (7) Flight tests should be conducted throughout all altitudes, maneuvers, and
control ranges while the system is instrumented as in paragraphs d(2) and (4) above to
determine that component ratings are not exceeded.

AC 27.1457. § 27.1457 (Amendment 27-22) COCKPIT VOICE RECORDER.

     a. Explanation. The function of the cockpit voice recorder (CVR) is to provide a
record of the crew communications preceding and during rotorcraft accidents. Over the
last several years, the National Transportation Safety Board (NTSB) has determined
that CVR’s are invaluable in determining probable cause of an accident. Because of
this fact and mandates of Congress, the use of CVR’s is required by the operating rules
on many rotorcraft involved in passenger-carrying operations.

     b. Procedures. The following areas are of particular consideration in the approval
of a CVR installation:

         (1) Equipment Qualifications. The CVR should be approved. The most
common way of obtaining an approval is to qualify the CVR (and associated control
panel, if appropriate) to TSO C84 or C123.


                                                       Page F - 99

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →