FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page F-98

PDF page 707 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 707
AC 27-1B · F-98Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

         (7) Extra caution should be exercised to ensure that control input forces at the
mechanical connection to the actuator pilot valves do not exceed their intended value.
Consideration should be given to the most adverse tolerance buildup in parts fabrication
and control system rigging.

         (8) The substantiating data should show that the hydraulic components will
perform their intended function reliably under the most adverse continuous and
short-time environmental conditions to which they are exposed. These variables
include but are not limited to temperature, humidity, vibration, altitude, and shock.
Paragraph AC 27.1309b(2)(i) contains a method of temperature correction to cover the
entire operating temperature envelope being certified.

         (9) The system component strength must be sufficient for its material fatigue
life to exceed the number of cycles imposed by pump ripple pressure.

      c.  Installation Precautions and Fire Protection.

         (1) All components and tubing routed through fire zones may be designed to
comply with the fire protection requirements of §§ 29.1183, 29.1185, and 29.1189. As
an alternative, a fireproof shield may be used around the component to be protected.
The component should be sufficiently protected to assure fluid leakage will not occur
and fuel the fire.

         (2) All hydraulic lines should be sufficiently isolated from the engine, bleed air
lines, environmental control unit, oil cooler, or other heat source to ensure expected line
life.

         (3) If flammable hydraulic fluid is used, the hydraulic components should be
isolated from ignition sources to ensure that failure of any of the hydraulic components
will not result in a fire or explosion. In the case of electrical ignition sources in the
proximity of hydraulic components, the electrical equipment should be hermetically
sealed or otherwise substantiated as not being an ignition source (reference
paragraph AC 27.1309b(1)(i)).

         (4) The installation detail should be thoroughly reviewed for adequacy of line
clamping and clearance from sharp edges. As much physical separation as possible
should be provided between hydraulic lines and electrical cables.

         (5) While the control system is being moved from stop to stop, observation
should be made to determine that hose flexing and tube bending is minimized.

     d. Testing.





Page F - 98

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →