FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page F-88

PDF page 697 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 697
AC 27-1B · F-88Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

must be accounted for in performance, engine operating characteristics, and inlet
distortion.

               (vi)  The handling qualities of the rotorcraft must be substantiated if ice can
accumulate on any surface. When ice can accumulate on unprotected surfaces, the
rotorcraft must exhibit satisfactory IFR handling qualities. In addition, following the
failure of the deice system, the rotorcraft must be safely controllable for 15 minutes, i.e.,
the rotorcraft must be free from excessive and rapid divergence.  Artificial ice shapes
may be acceptable for acquisition of flight test data necessary for handling qualities and
performance evaluations and demonstrations.

                (vii)  Items such as fuel tank vents, cooling vents, antennas, etc., should be
substantiated for maximum icing effects.

                 (viii) The ice protection system should be sufficiently reliable to perform its
intended function in accordance with the requirements of § 27.1309. These
requirements may in some instances be met by the use of sound engineering judgment
during design and compliance demonstrations. In many instances, use of good design
practices, failure modes and effects analysis, and similarity analyses combined with
good judgment will be adequate. In some instances the need for reliability analyses
may be desirable. Additional information pertaining to reliability is contained in
paragraph AC 27.1309 (§ 27.1309).

               (ix)  The subject of lightning should be addressed. The criteria applied on
rotorcraft with ice protection systems are that “the rotorcraft should be protected in such
a manner to minimize lightning risk.” The general rules of § 27.1309(a), (b), and (c) are
applicable to ensure adequate lightning protection. (Amendment 27-21,
November 6, 1984, added lightning protection requirements in § 27.610.)

              (x)   Ice protection of pitot-static sources, windshields, inlets, exposed
control linkages, etc., should be considered.

               (xi)  The impact of ice protection system failure, complete and partial, and
achieving adequate warning thereof should be assessed.

                (xii)  The impact of delayed application of ice protection systems should be
assessed. Hazardous conditions should not be apparent. Any rotorcraft characteristic
changes resulting should be covered in cautionary material in the rotorcraft flight
manual.

                 (xiii)  Possible droop stop malfunction with ice accumulation and its
potential hazard to the rotorcraft, its occupants, and ground personnel should be
assessed.





Page F - 88

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →