Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
3/31/2014 AC 27-1B, Chg 4
performance may be depreciated. The useful life of the engine may, therefore, be
extended at a dollar savings to the operator.
(C) Although installed performance is the primary topic in this discussion,
considerations must be given to other operational characteristics and systems which
may be affected by deteriorated engine power. These include:
(1) Engine characteristics (§ 27.939). Surge margin, engine response,
and air-restart capability might be affected and should be addressed, but flight testing
may not be required depending on the individual engine or aircraft installation and fuel
scheduling mechanism.
(2) Performance of customer bleed air systems may be degraded slightly.
No problem would be anticipated unless certain items within the system depend on a
critical engine bleed air pressure for their function.
(3) The maximum attainable gas producer speed, and thus power
available under certain ambients, may be affected if engine bleed air pressure is an
input to the fuel scheduling mechanism.
(4) Systems for surge protection which schedule on engine bleed air
pressure such as bleed valves, flow fences, bleed bands, and variable inlet guide vanes
may be influenced. The effect would normally be negligible unless when installed, the
installation losses, combined with reduced engine bleed air pressure because of
deterioration, would cause the bleed device to open and reduce power at any one of the
engine ratings.
(ii) Procedures.
(A) The need for flight tests to verify predicted power available with
deteriorated engines depends on the scope of testing which occurred during initial
certification. If the original rotorcraft certification included flight testing as described in
paragraph b.(5) (engine power-turboshaft engines) herein for validation of power
available, the need for a demonstration with deteriorated engines is greatly diminished
and perhaps eliminated.
(B) If flight testing to verify deteriorated engine power available is deemed
necessary, the procedure used would be the same as that described in paragraph b.(5)
(engine power-turboshaft engines), except that the data would be corrected downward
to a deteriorated engine runline. Efforts should concentrate on obtaining data in areas
of the operational envelope where maximum gas producer speed is likely to be attained,
or where bleed valves or other devices which schedule on gas producer discharge
pressure are likely to function. On many installations maximum gas producer speed will
occur with cold temperatures and high altitudes; bleed valves and other devices which
schedule on gas producer discharge pressure are most likely to function and reduce
power on a hot day at low altitude.
Page B - 17
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.