Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 3/31/2014
(E) Power available data should be obtained throughout the test program at
various ambient conditions. Some engines have devices which restrict the mechanical
NG speed to a constant corrected speed at cold temperatures. Others may limit power
to a fuel flow value which would be encountered only at certain ambients. Others may
limit by torque limiting devices. Therefore, power available data should be obtained at
various ambients to verify that all limiting devices are functioning properly and have not
been affected by the installation.
(F) Through use, turbine engine power capabilities decrease with time. This
is called engine deterioration. Deterioration is largely a function of the particular engine
design, the manner, and the environment in which the engine is operated. There is a
need, therefore, to provide a method which can be used in service to periodically
determine the level of engine deterioration. A power assurance curve is usually
provided to allow the flightcrew to know the power producing capabilities of any engine.
A power assurance check is a check of the engine(s) which will determine that the
engine(s) can produce the power required to achieve flight manual performance. This
check does not have to be done at maximum engine power. Figure AC 27.45-6 is a
typical power assurance curve for an installed engine showing minimum acceptable
torque which assures that power is available to meet the RFM performance. Some
power assurance curves have maximum allowable NG limits that must not be exceeded
for a given torque value. An in-flight power assurance check may be used in addition to
the pretakeoff check. The validation of either check must be done by the methodology
used to determine the installed minimum specification engine power available. For the
in-flight power assurance check there must be full accountability for increased efficiency
due to such items as inlet ram recovery, absence of exhaust reingestion, etc. A power
assurance check done statically and one conducted in-flight must yield the same torque
margin(s). An engine may pass power assurance at low power but still may not be
capable of producing the rated power values. This occurs when the curve of corrected
power and corrected temperature for the engine intersects the minimum uninstalled
specification engine curve. If this condition exists, the entire power assurance and
power available information may need to be reestablished.
(6) Deteriorated Engine Power - Turboshaft Engine.
(i) Background.
(A) A specific engine model may have been certificated for operation with
power which has “normally” deteriorated below specification. This “normal”
deterioration refers to a gradual loss in engine performance, possibly caused by
compressor erosion, as opposed to a sudden performance loss which may be due to
mechanical damage. The application for deteriorated engine power should not be
confused with the installed mechanical engine derating which is frequently used to
match transmission and engine power capabilities.
(B) The use of deteriorated power is intended to allow continued operations
with an engine which is serviceable and structurally sound, although aircraft
Page B - 16
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.