Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
3/31/2014 AC 27-1B, Chg 4
temperatures. The data should be obtained at the actual flight condition for which the
performance is to be presented (i.e., hover, climb, or cruise).
(B) Following a power increase, engine temperature or RPM can significantly
decrease for a period of time as torque is held constant. Said another way, torque will
increase if RPM or temperature are held constant. This is a characteristic typical of
turbine engines due largely to expansion of turbine blades and reduced clearances in
the engine. Some engines may show a temperature increase at constant power due to
engine or temperature sensing system peculiarities. An engine will usually establish a
stabilized relationship of power parameters in approximately 2 or 3 minutes. For this
reason, the following procedure should be used when obtaining in-flight engine data.
(1) To determine the takeoff and 2 ½-minute values, first stabilize the
engine at a low power setting. After stabilization, rapidly increase the power demand to
takeoff or 2 ½-minute power levels. Record the engine parameters as soon as the
specification torque, temperature, or speed is attained. Care must be taken not to
exceed a limit. These readings should be obtained approximately 15 seconds after
power is initially applied.
(2) To determine the 30-minute and maximum continuous power values,
approximately 2 to 3 minutes of stabilization time after power is increased is generally
used, but up to 5 minutes stabilization time is allowed. The reason for the different
procedures is when a pilot requires takeoff or 2 ½-minute power values he is in a critical
flight condition and does not have the luxury of waiting for the engine(s) to produce
rated power. Stabilization time is allowed for the maximum continuous and 30-minute
ratings because these values are not associated with flight conditions for which power is
needed immediately.
(C) The in-flight measurements recorded with the engine(s) on the flight test
rotorcraft must be corrected downward if the test engine is above minimum specification
and corrected upward for a test engine that is below minimum specification. This
correction is necessary to verify that a minimum specification engine installed on a
production rotorcraft is capable of producing the power values used to compute the
flight manual performance without exceeding any engine limit. In addition, if the
production rotorcraft’s power measurement devices have significant (greater than 3
percent) power error, this error must be accounted for in a conservative manner.
(D) On multiengine rotorcraft, the engine location may result in different
installation losses between engines. If this condition exists, multiengine performance
should be based on the total power available after considering the different installation
losses and with minimum specification engines installed. OEI performance must be
based on the loss of the engine which has the lowest installation losses. Additionally,
the power losses due to such items as accessory bleed air, particle separators, engine
driven accessories, etc., must be accounted for accordingly.
Page B - 15
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.